SIL465000

**celpac[®]** 

S/CLP/SIL465000/A/17/01/2006 

page 1 /5 GB 

## **Power Solid State Relay With Analog Control, pitch 22.5mm compact size and DIN rail mounting.** 

- ❏ Ready to use Single-Phase Relay: Phase angle controller Transfer characterisic :Angle open loop Operating voltage :160 to 450V Operating Current :0.1 to 32A 

## **SIL465000** 

**Phase angle controller Output : 160-450VAC 32A(*) Input   : Analog 0-10V** 

- ❏ Wide variety of applications. 

- ❏ Main frequency range : 40 to 70 Hz with self adaptation 

- ❏ Analog control : Voltage 0-10V 

- ❏ Green LED visualization on the input 

- ❏ Relay without trimmer (factory setting) 

- ❏ Isolated internal power supply (taken from the mains) 

- ❏ Built in protection : RC and VDR 

- ❏ Mounting and dismounting on DIN rail without any tool or directly mountable on panel with screws. 

- ❏ Designed in conformity with EN60947-4-3 (IEC947-4-3) and EN60950 

- (*) see conditions, thermal curve page 4. ( 22A @ 40°C according IEC 947.4.3 ) 

**Typical  application:** 

## **Dimensions :** 

_**Proud to serve you**_ ~~eC~~ All technical caracteristics are subject to change without previous notice. Caractéristiques sujettes à modifications sans préavis. **[celduc] r     e     l     a     i     s[®]** 

~~S/CLP/SIL465000/A/17/01/2006~~ 

page 2 /5 GB 

## ~~**celpac[®]**~~ 

## _**Control characteristics (at 25°C)**_ 

|||||||
|---|---|---|---|---|---|
|**Paramètre / Parameter**|**Conditions**|**Symbol**|**Typ.**|**Unit**||
|Operatingcontrol voltage||Uc|0 to 10V|V||
|Maximum input voltage||Uc max|± 30V|V||
|Input resistor||Rc|20|kΩ||
|Input LED|||green|||
|Rise and fall time|see fig. 2|time|62|ms||
|Input immunity|IEC 1000-4-4(burst)||2kV|||
|Input immunity|IEC 1000-4-5(schocks)||2KV|||



## _**Output characteristics (at 25°C)**_ 

|**_Parameter_**|**Conditions**|**Symbol**|**Typ.**|**Unit**|
|---|---|---|---|---|
|Load voltage||Ue|400|V rms|
|Operatingrange||Uemin-max|160-450|V rms|
|Peak voltage||Up|1200|V|
|Mains frequencyrange||fm|40-70|Hz|
|Clampingvoltage||Uclamp|820(@1mA)|V|
|internalpower supplycurrent counsomption(from mains)|@Ue,50Hz|Ie|6|mA rms|
|AC-51 nominal current :permanent|**_( see Fig. 4page 4)_**|Ie AC-51|**32**|A rms|
|AC-53 nominal current||Ie AC-53|12|A rms|
|Non repetitive overload current|tp=10ms_(Fig. 3)_|Itsm|550|A|
|On state voltage drop (typical value)|@25°C|Vt|0,9|V|
|Dynamic resistance(typical value)||rt|8|mΩ|
|Output Power dissipation  (typical value for full conduction)||Pd|0,81xIe+0,08xIe2|W|
|Thermal resistance betweenjunction to air||Rthj/a|3,3(2,5)|K/W|
|Off state leakage current|@Ue,50Hz|Ilk|<5|mA|
|Minimum load current||Iemin|100|mA|
|Rise and fall time|@50Hz see fig. 2|tau|15|ms|
|Delaytime|@50Hz see fig. 2|td max|20|ms|
|Power upinitialisation time|@Ue,50Hz|t init.|160|ms|
|Off state dv/dt||dv/dt|500|V/µs|
|Maximum non repetitive di/dt||di/dt|50|A/µs|
|I2t(<10ms)||I2t|1500|A2s|
|Conducted immunitylevel|IEC 1000-4-4(burst)||4kV criterion B||
|Conducted immunitylevel|IEC 1000-4-5(schocks)||4kV criterion B||
|Short circuitprotection|FERRAZ|gRC 25A/32A/50A/63A 14x51|||



|**_General characteristics(at 25°C)_**|**_General characteristics(at 25°C)_**|**_General characteristics(at 25°C)_**|**_General characteristics(at 25°C)_**|
|---|---|---|---|
|Input to output insulation voltage|Ui|4000|VRMS|
|Output to case insulation voltage|Ui|4000|VRMS|
|Insulation resistance|Ri|100(@500VDC)|MΩ|
|Rated impulse voltage|Uimp|4000|V|
|Protection level /  IEC 529|-|IP20||
|Pollution degree|-|2||
|Vibration resistance 10 -55 Hz accordingto CEI68 :|double  amplitude|(not tested)||
|Shocks resistance accordingto CEI68(on DIN rail / with screws)|-|30/50|g|
|Ambient temperature(with no icingor condensation)|-|-20 /+70|°C|
|Storage temperature(with no icingor condensation)||-40/+100|°C|
|Ambient humidity|HR|40 to 85|%|
|Weight||270|g|
|Conformity||EN60947-4-3(IEC60947-4-3)||
|||||



~~S/CLP/SIL465000/A/17/01/2006~~ 

page 3 /5 GB 

## ~~**celpac[®]**~~ 

_**Transfer characteristics (at 25°C)**_ 

|**Paramètre /****_Parameter_**|**Conditions**|**Symbol**|**Min**|**Nom**|**Max**|**Unit**|
|---|---|---|---|---|---|---|
|Operatinganalogvoltage|Us|||0-10||V|
|Minimum release voltage|||0,1|||V|
|Uload/Ue(@ Ue typ.)|@ Uc=10V|||>98||%|
|Tranfer accuracy||||2||%|
|Transfer type||angle linear(see Fig. 1)|||||



## **Fig. 2 : Timing (Switch ON) @50Hz** 

## **Fig.1   Transfer characteric :** 

## **Other possibilities with SIL4 series :(consult us)** 

- With trimmer for  minimum step level setting: 

- With trimmer for fall and rise time setting: 

- Type of soft fall and rise time :linear or exponential 

- Transfer characteristic: angle, RMS, power 

- Analog input :0 - 5V, 4 - 20mA, ... 

- Mains frequency range 

- Mains voltage range 

- Operating current 

**celduc ® r     e     l     a     i     s** 

~~**www.celduc.com**~~ 

**5, Rue Ampère BP30004     42290 SORBIERS - FRANCE        E-mail : celduc-relais@celduc.com Fax +33 (0) 4 77 53 85 51            Service Commercial France Tél. : +33 (0) 4 77 53 90 20 Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21    Sales Dept. Asia : Tél. +33 (0) 4 77 53 90 19** 

~~S/CLP/SIL465000/A/17/01/2006~~ 

page 4 /5 GB 

## ~~**celpac[®]**~~ 

## _**Thermal specifications**_ **.** 

- ♦ _**The curve "1"** gives the limits of the product. The temperature reached are acceptable for the components. These values are in compliance with most of SSRs manufacturers. In a cabinet with a minimum of ventilation or a non permanent current, these values are correct._ 

- ♦ _**The curve "2"** gives the limits of the product according to EN60947-4-3 with a maximum rise temperature of 50°C (@40°C) for a permanent working and in air calm ( test during 8 hours)._ 

- ♦ _For a non permanent current, you can calcule the average power = Pd x duty cycle and check the rise temperature :_ Δ _Tj = Pd x Rthj/a (Pd and Rthj/a are given page 2)). The junction temperature must not exceed 125°C at the maximum ambient temperature._ _**The maximum current is limited to the size of the thyristors = 50A.**_ 

- ♦ _The thermal constant (Cth) of the product is 7 minutes. That means the rise temperature is only 63% of the stabilized temperature after a running time of 7 minutes._ 

## _**Overload current**_ **.** 

1 - _No repetitive Itsm is given  without voltage reapplied . This curve is used for the determination of the protection._ 

2 - _Repetitive Itsm  is given for inrush current with initial Tj = 70°C. In normal working , this curve musn't be exceed. Be carefull, the repetition of the surge current decrease the lifetime  SSR's ._ 

fig 3 

_Mounting and dismounting on DIN rail without any tool. Panel Mounting_ 

♦ _**Warning** !  semiconductor relays don't provide any galvanic insulation between the load and the mains. Always use in conjunction with an adapted circuit breaker with isolation feature  or a similar device in order to  ensure a reliable isolation in the event of wrong function and when the relay must be insulated from the mains (maintenance ; if not used for a long duration ...)._ 

## **celduc ®** 

~~**www.celduc.com**~~ 

**r     e     l     a     i     s 5, Rue Ampère BP30004     42290 SORBIERS - FRANCE        E-mail : celduc-relais@celduc.com Fax +33 (0) 4 77 53 85 51            Service Commercial France Tél. : +33 (0) 4 77 53 90 20 Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21    Sales Dept. Asia : Tél. +33 (0) 4 77 53 90 19** 

~~S/CLP/SIL465000/A/17/01/2006~~ 

## ~~**celpac[®]**~~ 

## _**Connections**_ **.** 

- ♦ _For the output terminals, the wire cross sections must be_ 

- _adapted to the load current and to the overcurrent protection device characteristics. The relay rated voltage must be adapted to the mains rated voltage._ a| 

   - ♦ **celpac** _use screw clamp connections._ 

## page 5 /5 GB 

|wires<br>(mm2)<br>L<br>L|torques|screwdrive|
|---|---|---|
|**control**<br>1 x(0,75-->2,5)<br>L = 6mm|0,4N.m<br>(0,6N.m max)|3,5x0,5mm|
|**Power**<br>1x(1,5-->16)   1 x(1,5-->10)<br>L = 10mm|1,2N.m<br>(1,8N.m max)|Pozidriv2/<br>0,8x5,5 (1x6)|



## _**Mounting**_ 

## ♦ _**Only in vertical position:**_ 

_The user should protect heat sensitive materials as well as persons against any contacts with the heatsink. For non vertical mounting , the load current must be 50% lower than the rated one . For a good cooling, the SSR needs an air convection. Less convection air produces an abnormal heating. Keep a distance between  the upper SSR and the lower SSR. In case of no space between two SSR (zero space between two SSRs) , please reduce the load current. For further details refer to below :_ ♦ ~~—_—<—$—$—_$_—_<—$—$—$—_$_—<—<¥_<_$_—=£—£_>_=_£{£__>_{_—_—_—_—_—_—_—_—_—_————~~ _**Derating current with no space between SSRs**_ 

_AC-51 nominal currents are given with a space of 22,5mm between each SSR, for a_ 

_permanent current during a minimum time of 8 hours in air calm according to IEC60947-4-3. In case of non permanent currents or in case of SSRs are mounted with no space, you must check the heatsink temperature never exceed 90°C. When the SSRs are mounted side to side ( no space between each relay) a derating current of 25% must be take into account._ 

_A forced cooling ( fan inside the cabinet) improves significantly the thermal performances._ 

## _**Typical application  :**_ 

## ~~_—__~~ _**LOADS**_ 

_SILD product is designed mainly for AC-51 résistive load. AC-53 motor current are also given . For other loads, check the inrush current at turn ON and possible overvoltages at turn OFF or consult us :_ 

_* AC-55b : Incandescent lamps : Inrush current is generally 10 times In during few 10ms. So limit the nominal current at about 15A._ 

_* AC-55a : Electric discharge lamp : These loads often have overcurrent at turn ON and overvoltage at turn OFF, so we advise to use 400VAC SSR on 230VAC mains._ 

_* AC-56a : Transformers loads : Very high inrush current up to 100 times In . We advise to use random SSR._ 

## _**Protection :**_ 

_To protect the  SSR against a short-circuit of the load , use a fuse with a I[2] t value = 1/2 I[2] t  value specified page 2. A test has been made with FERRAZ fuse ( see page 2)._ 

_It is possible to protect SSR by MCB ( miniature circuit breaker). In this case, see application note (_ 

_SSR protection) and use a SSR with high I[2] t value (5000A[2] s minimum)._ 

## _**EMC :**_ 

## ♦ **Immunity :** 

_We give in our data-sheets, the immunity level of our SSRs according to the main standards for this type of products : EN61000-4-4 &5. You can see the high immunity level in comparison with the products on the market._ 

> ♦ ~~———~~ **Emission:** 

_SSRs are complex devices which must be interconnected with other equipment (loads, cables,etc.) to form a system. Because the other equipment or the interconnections may not be under the control of_ **celduc** _, it shall be the responsibility of the system integrator to ensure that systems containing SSRs comply with the requirements of any rules and regulations applicable at the system level.. Consult_ **celduc** _laboratory which can make some tests in your application._ 

## **celduc ®** 

~~**www.celduc.com**~~ 

**r     e     l     a     i     s** 

**5, Rue Ampère BP30004     42290 SORBIERS - FRANCE        E-mail : celduc-relais@celduc.com Fax +33 (0) 4 77 53 85 51            Service Commercial France Tél. : +33 (0) 4 77 53 90 20 Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21    Sales Dept. Asia : Tél. +33 (0) 4 77 53 90 19**