RPB-1600-48

**-** 1600W Intelligent Single Output Battery Charger **RPB 1600 series** 

BauarSicherheitbeegelodwacmat geprufto ges g www.ID 2000000000tuv.com wie) 2) **UL60950-1** FAs **EN60950-1** ~~2~~ **TPTC004** FAL **IEC60950-1** CB C€ ■ 

## ■ 

## ■ 

## ■ 

_File Name:RPB-1600-SPEC   2019-09-25_ 

## 1600W Intelligent Single Output Battery Charger 

## **- RPB 1600 series** 

## **SPECIFICATION** 

|**RPB-1600-12**<br>**RPB-1600-24**<br>**MODEL**<br>**OUTPUT**<br>**VOLTAGE RANGE**<br>**Note.4**<br>**FREQUENCY RANGE**<br>**POWER FACTOR (Typ.)**<br>**EFFICIENCY (Typ.)**<br>**INPUT**<br>**INRUSH CURRENT (Typ.)**<br>**LEAKAGE CURRENT**<br>**AC CURRENT (Typ.)**<br>**Note.4**<br>90 ~ 264VAC          127 ~ 370VDC<br>47 ~ 63Hz<br>0.97/230VAC at full load<br>91%<br>14A/115VAC     8A/230VAC<br>COLD START 35A/230VAC<br><2mA / 240VAC<br>**RPB-1600-48**<br>92.5%<br>15A/115VAC          8.5A/230VAC<br>93.5%<br>**OVER TEMPERATURE**<br>**OVER VOLTAGE**<br>15.75 ~ 18.75V<br>Protection type : Shut down o/p voltage, re-power on to recover<br>Shut down o/p voltage, recovers automatically after temperature goes down<br>31.5 ~ 37.5V<br>63 ~ 75V<br>**PROTECTION**<br>**REMOTE ON-OFF CONTROL**<br>**OUTPUT VOLTAGE**<br>**PROGRAMMABLE(PV) Note 5**<br>**OUTPUT CURRENT**<br>**PROGRAMMABLE(PC) Note 5**<br>By electrical signal or dry contact     Power ON:short     Power OFF:open. Please refer to Function Manual<br>**FUNCTION**<br>**WORKING TEMP.**<br>**WORKING HUMIDITY**<br>**STORAGE TEMP., HUMIDITY**<br>**TEMP. COEFFICIENT**<br>**VIBRATION**<br>-30 ~ +70<br>(Refer to "Derating Curve")<br>℃<br>20 ~ 90% RH non-condensing<br>-40 ~ +85<br>, 10 ~ 95% RH non-condensing<br>℃<br>±<br>℃<br>℃<br>0.03%/<br>(0 ~ 50<br>)<br>**ENVIRONMENT**<br>10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes<br>**SAFETY STANDARDS**<br>**WITHSTAND VOLTAGE**<br>UL60950-1, TUV EN60950-1,<br>approved<br>EAC TP TC 004<br>I/P-O/P:3KVAC     I/P-FG:2KVAC     O/P-FG:1.5KVAC<br>**ISOLATION RESISTANCE**<br>**MTBF**<br>**DIMENSION**<br>**PACKING**<br>**OTHERS**<br>154K hrs min.<br>Telcordia SR-332 (Bellcore) ; 100.3K hrs min.      MIL-HDBK-217F (25<br>)<br>℃<br>300*85*41mm (L*W*H)<br>**SAFETY &**<br>**EMC**<br>**(Note 6)**<br>I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25<br>/ 70% RH<br>℃<br>1.8Kg;6pcs/11.8Kg/1.3CUFT<br>**NOTE**<br>℃<br>℃<br>℃<br>**BOOST CHARGE  VOLTAGE(Vboost)(default)**<br>**FLOAT CHARGE  VOLTAGE(Vfloat)(default)**<br>**LEAKAGE CURRENT FROM**<br>**BATTERY (Typ.)**<br>**Note.8**<br>**RECOMMENDED BATTERY**<br>**CAPACITY(AMP HOURS) Note.3**<br>14.4V<br>28.8V<br>57.6V<br>13.8V<br><45mA<br>33<br>10<br>0 ~<br>00Ah<br>27.6V<br>55.2V<br>23.5 ~ 30V<br>47.5 ~ 58.8V<br>1 0 ~ 50Ah<br>8<br>5<br>9<br>270<br>0 ~<br>Ah<br>**VOLTAGE ADJ RANGE**<br>.<br>**Note 5** 11.5 ~ 15V<br>**TEMPERATURE COMPENSATION** -3mV /<br>/ cell / (12V = 6 cells ; 24V = 12 cells ; 48V = 24 cells)<br>℃<br>Adjustment of output voltage is allowable to 75 ~ 125% of nominal output voltage<br>Please refer to the Function Manual.<br>Please refer to the Function Manual.<br>Adjustment of output current is allowable to 20 ~ 100% of rated current<br>By built-in potentiometer, SVR<br>**AUXILIARY POWER**<br>5V @ 0.3A, 12V @ 0.8A<br>Compliance to EN61000-4-2,3,4,5,6,8,11, EN61000-6-2 (EN50082-2), Heavy industry level, criteria A,EAC TP TC 020<br>Compliance to EN55032 (CISPR32) Conduction Class B, Radiation Class A ; EN61000-3-2,-3,EAC TP TC 020<br>**EMC IMMUNITY**<br>**EMC EMISSION**<br>**ALARM SIGNAL**<br>Isolated signal output for T-alarm and DC OK<br>**CONSTANT CURRENT(CC)(default)** 100A<br>55A<br>27.5A<br>~~SSS~~<br>1. Modification for charger specification may be required for different battery specification. Please contact battery vendor and MEAN WELL for details.<br>2. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25<br>of ambient temperature.<br>3. This is MEAN WELL's suggested range. Please consult your battery manufacturer for their suggestions about maximum charging current limitation.<br>4. Derating may be needed under low input voltages. Please check the derating curve for more details.<br>5. PV/PC functions when users are not operating on PMBus/CANBus. SVR functions when users are neither operating on PMBus/CANBus nor using PV/PC.<br>6. The charger is considered a component which will be installed into a final equipment. All the EMC tests are been executed by mounting the unit on<br>a 720mm*360mm metal plate with 1mm of thickness. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to<br>perform these EMC tests, please refer to “EMI testing of component power supplies.” (as available on http:/Wwww.meanwell.com)<br>7. The ambient temperature derating of 3.5<br>/1000m with fanless models and of<br>5<br>/1000m with fan models for operating altitude higher than 2000m(6500ft).<br>8. When charging lead acid battery or battery without BMS, use breaker to disconnect charger and battery after fully charged.|**RPB-1600-12**<br>**RPB-1600-24**<br>**MODEL**<br>**OUTPUT**<br>**VOLTAGE RANGE**<br>**Note.4**<br>**FREQUENCY RANGE**<br>**POWER FACTOR (Typ.)**<br>**EFFICIENCY (Typ.)**<br>**INPUT**<br>**INRUSH CURRENT (Typ.)**<br>**LEAKAGE CURRENT**<br>**AC CURRENT (Typ.)**<br>**Note.4**<br>90 ~ 264VAC          127 ~ 370VDC<br>47 ~ 63Hz<br>0.97/230VAC at full load<br>91%<br>14A/115VAC     8A/230VAC<br>COLD START 35A/230VAC<br><2mA / 240VAC<br>**RPB-1600-48**<br>92.5%<br>15A/115VAC          8.5A/230VAC<br>93.5%<br>**OVER TEMPERATURE**<br>**OVER VOLTAGE**<br>15.75 ~ 18.75V<br>Protection type : Shut down o/p voltage, re-power on to recover<br>Shut down o/p voltage, recovers automatically after temperature goes down<br>31.5 ~ 37.5V<br>63 ~ 75V<br>**PROTECTION**<br>**REMOTE ON-OFF CONTROL**<br>**OUTPUT VOLTAGE**<br>**PROGRAMMABLE(PV) Note 5**<br>**OUTPUT CURRENT**<br>**PROGRAMMABLE(PC) Note 5**<br>By electrical signal or dry contact     Power ON:short     Power OFF:open. Please refer to Function Manual<br>**FUNCTION**<br>**WORKING TEMP.**<br>**WORKING HUMIDITY**<br>**STORAGE TEMP., HUMIDITY**<br>**TEMP. COEFFICIENT**<br>**VIBRATION**<br>-30 ~ +70<br>(Refer to "Derating Curve")<br>℃<br>20 ~ 90% RH non-condensing<br>-40 ~ +85<br>, 10 ~ 95% RH non-condensing<br>℃<br>±<br>℃<br>℃<br>0.03%/<br>(0 ~ 50<br>)<br>**ENVIRONMENT**<br>10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes<br>**SAFETY STANDARDS**<br>**WITHSTAND VOLTAGE**<br>UL60950-1, TUV EN60950-1,<br>approved<br>EAC TP TC 004<br>I/P-O/P:3KVAC     I/P-FG:2KVAC     O/P-FG:1.5KVAC<br>**ISOLATION RESISTANCE**<br>**MTBF**<br>**DIMENSION**<br>**PACKING**<br>**OTHERS**<br>154K hrs min.<br>Telcordia SR-332 (Bellcore) ; 100.3K hrs min.      MIL-HDBK-217F (25<br>)<br>℃<br>300*85*41mm (L*W*H)<br>**SAFETY &**<br>**EMC**<br>**(Note 6)**<br>I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25<br>/ 70% RH<br>℃<br>1.8Kg;6pcs/11.8Kg/1.3CUFT<br>**NOTE**<br>℃<br>℃<br>℃<br>**BOOST CHARGE  VOLTAGE(Vboost)(default)**<br>**FLOAT CHARGE  VOLTAGE(Vfloat)(default)**<br>**LEAKAGE CURRENT FROM**<br>**BATTERY (Typ.)**<br>**Note.8**<br>**RECOMMENDED BATTERY**<br>**CAPACITY(AMP HOURS) Note.3**<br>14.4V<br>28.8V<br>57.6V<br>13.8V<br><45mA<br>33<br>10<br>0 ~<br>00Ah<br>27.6V<br>55.2V<br>23.5 ~ 30V<br>47.5 ~ 58.8V<br>1 0 ~ 50Ah<br>8<br>5<br>9<br>270<br>0 ~<br>Ah<br>**VOLTAGE ADJ RANGE**<br>.<br>**Note 5** 11.5 ~ 15V<br>**TEMPERATURE COMPENSATION** -3mV /<br>/ cell / (12V = 6 cells ; 24V = 12 cells ; 48V = 24 cells)<br>℃<br>Adjustment of output voltage is allowable to 75 ~ 125% of nominal output voltage<br>Please refer to the Function Manual.<br>Please refer to the Function Manual.<br>Adjustment of output current is allowable to 20 ~ 100% of rated current<br>By built-in potentiometer, SVR<br>**AUXILIARY POWER**<br>5V @ 0.3A, 12V @ 0.8A<br>Compliance to EN61000-4-2,3,4,5,6,8,11, EN61000-6-2 (EN50082-2), Heavy industry level, criteria A,EAC TP TC 020<br>Compliance to EN55032 (CISPR32) Conduction Class B, Radiation Class A ; EN61000-3-2,-3,EAC TP TC 020<br>**EMC IMMUNITY**<br>**EMC EMISSION**<br>**ALARM SIGNAL**<br>Isolated signal output for T-alarm and DC OK<br>**CONSTANT CURRENT(CC)(default)** 100A<br>55A<br>27.5A<br>~~SSS~~<br>1. Modification for charger specification may be required for different battery specification. Please contact battery vendor and MEAN WELL for details.<br>2. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25<br>of ambient temperature.<br>3. This is MEAN WELL's suggested range. Please consult your battery manufacturer for their suggestions about maximum charging current limitation.<br>4. Derating may be needed under low input voltages. Please check the derating curve for more details.<br>5. PV/PC functions when users are not operating on PMBus/CANBus. SVR functions when users are neither operating on PMBus/CANBus nor using PV/PC.<br>6. The charger is considered a component which will be installed into a final equipment. All the EMC tests are been executed by mounting the unit on<br>a 720mm*360mm metal plate with 1mm of thickness. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to<br>perform these EMC tests, please refer to “EMI testing of component power supplies.” (as available on http:/Wwww.meanwell.com)<br>7. The ambient temperature derating of 3.5<br>/1000m with fanless models and of<br>5<br>/1000m with fan models for operating altitude higher than 2000m(6500ft).<br>8. When charging lead acid battery or battery without BMS, use breaker to disconnect charger and battery after fully charged.|**RPB-1600-12**|**RPB-1600-24**|**RPB-1600-48**|
|---|---|---|---|---|
||**BOOST CHARGE  VOLTAGE(Vboost)(default)**|14.4V|28.8V|57.6V|
||**FLOAT CHARGE  VOLTAGE(Vfloat)(default)**|13.8V|27.6V|55.2V|
||**CONSTANT CURRENT(CC)(default)**|100A|55A|27.5A|
||**VOLTAGE ADJ RANGE**<br>.<br>**Note 5**|23.5 ~ 30V<br>47.5 ~ 58.8V<br> 11.5 ~ 15V<br>By built-in potentiometer, SVR|||
||**RECOMMENDED BATTERY**<br>**CAPACITY(AMP HOURS) Note.3**|33<br>10<br>0 ~<br>00Ah|1 0 ~ 50Ah<br>8<br>5|9<br>270<br>0 ~<br>Ah|
||**LEAKAGE CURRENT FROM**<br>**BATTERY (Typ.)**<br>**Note.8**|<45mA|||
||**VOLTAGE RANGE**<br>**Note.4**|90 ~ 264VAC          127 ~ 370VDC|||
||**FREQUENCY RANGE**|47 ~ 63Hz|||
||**POWER FACTOR (Typ.)**|0.97/230VAC at full load|||
||**EFFICIENCY (Typ.)**|91%|92.5%|93.5%|
||**AC CURRENT (Typ.)**<br>**Note.4**|14A/115VAC     8A/230VAC|15A/115VAC          8.5A/230VAC||
||**INRUSH CURRENT (Typ.)**|COLD START 35A/230VAC|||
||**LEAKAGE CURRENT**|<2mA / 240VAC|||
||**OVER VOLTAGE**|15.75 ~ 18.75V<br>Protection type : Shut down o/p voltage, re-power on to recover<br>31.5 ~ 37.5V<br>63 ~ 75V|||
||**OVER TEMPERATURE**|Shut down o/p voltage, recovers automatically after temperature goes down|||
||**AUXILIARY POWER**|5V @ 0.3A, 12V @ 0.8A|||
||**REMOTE ON-OFF CONTROL**|By electrical signal or dry contact     Power ON:short     Power OFF:open. Please refer to Function Manual|||
||**OUTPUT VOLTAGE**<br>**PROGRAMMABLE(PV) Note 5**|Adjustment of output voltage is allowable to 75 ~ 125% of nominal output voltage<br>Please refer to the Function Manual.|||
||**OUTPUT CURRENT**<br>**PROGRAMMABLE(PC) Note 5**|Please refer to the Function Manual.<br>Adjustment of output current is allowable to 20 ~ 100% of rated current|||
||**TEMPERATURE COMPENSATION**|-3mV /<br>/ cell / (12V = 6 cells ; 24V = 12 cells ; 48V = 24 cells)<br>℃|||
||**ALARM SIGNAL**|Isolated signal output for T-alarm and DC OK|||
||**WORKING TEMP.**|-30 ~ +70<br>(Refer to "Derating Curve")<br>℃|||
||**WORKING HUMIDITY**|20 ~ 90% RH non-condensing|||
||**STORAGE TEMP., HUMIDITY**|-40 ~ +85<br>, 10 ~ 95% RH non-condensing<br>℃|||
||**TEMP. COEFFICIENT**|±<br>℃<br>℃<br>0.03%/<br>(0 ~ 50<br>)|||
||**VIBRATION**<br>~~SSS~~|10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes<br>~~SSS~~|||
||**SAFETY STANDARDS**<br>~~SSS~~|UL60950-1, TUV EN60950-1,<br>approved<br>EAC TP TC 004<br>~~SSS~~|||
||**WITHSTAND VOLTAGE**<br>~~SSS~~|I/P-O/P:3KVAC     I/P-FG:2KVAC     O/P-FG:1.5KVAC<br>~~SSS~~|||
||**ISOLATION RESISTANCE**<br>~~SSS~~|I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25<br>/ 70% RH<br>℃<br>~~SSS~~|||
||**EMC EMISSION**<br>~~SSS~~|Compliance to EN55032 (CISPR32) Conduction Class B, Radiation Class A ; EN61000-3-2,-3,EAC TP TC 020<br>~~SSS~~|||
||**EMC IMMUNITY**<br>~~SSS~~|Compliance to EN61000-4-2,3,4,5,6,8,11, EN61000-6-2 (EN50082-2), Heavy industry level, criteria A,EAC TP TC 020<br>~~SSS~~|||
||**MTBF**<br>~~SSS~~|154K hrs min.<br>Telcordia SR-332 (Bellcore) ; 100.3K hrs min.      MIL-HDBK-217F (25<br>)<br>℃<br>~~SSS~~|||
||**DIMENSION**|300*85*41mm (L*W*H)|||
||**PACKING**<br>1.8Kg;6pcs/11.8Kg/1.3CUFT<br>℃<br>℃<br>℃<br>1. Modification for charger specification may be required for different battery specification. Please contact battery vendor and MEAN WELL for details.<br>2. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25<br>of ambient temperature.<br>3. This is MEAN WELL's suggested range. Please consult your battery manufacturer for their suggestions about maximum charging current limitation.<br>4. Derating may be needed under low input voltages. Please check the derating curve for more details.<br>5. PV/PC functions when users are not operating on PMBus/CANBus. SVR functions when users are neither operating on PMBus/CANBus nor using PV/PC.<br>6. The charger is considered a component which will be installed into a final equipment. All the EMC tests are been executed by mounting the unit on<br>a 720mm*360mm metal plate with 1mm of thickness. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to<br>perform these EMC tests, please refer to “EMI testing of component power supplies.” (as available on http:/Wwww.meanwell.com)<br>7. The ambient temperature derating of 3.5<br>/1000m with fanless models and of<br>5<br>/1000m with fan models for operating altitude higher than 2000m(6500ft).<br>8. When charging lead acid battery or battery without BMS, use breaker to disconnect charger and battery after fully charged.||||



_File Name:RPB-1600-SPEC   2019-09-25_ 

## 1600W Intelligent Single Output Battery Charger 

## **- RPB 1600 series** 

## **Block Diagram** 

**==> picture [499 x 407] intentionally omitted <==**

**----- Start of picture text -----**<br>
PFC fosc : 90KHz<br>PWM fosc : 70KHz<br>I/P FILTEREMI CURRENTLIMITINGINRUSHACTIVE RECTIFIERSPFC& SWITCHINGPOWER RECTIFIERSFILTER& ORINGFET -V+V<br>O.V.P.<br>ORING  FET<br>CONTROL<br>PFC PWM DETECTION PV/PC<br>CONTROL CONTROL CIRCUIT<br>TRANSCEIVERS DA/DB<br>DETECTIONCIRCUIT MCU MCU ISOLATIONDATA T-AlarmDC-OK<br>SDA/SCL<br>O.T.P. (CANH/CANL)<br>AUX FAN RECTIFIERS 12V/0.8A Remote ON-OFF<br>POWER & AUX POWER<br>FILTER 5V/0.3A<br>Derating Curve Static Characteristics<br>100<br>100<br>90<br>80 80<br>230VAC<br>Input only 70<br>60<br>50 60<br>40 50<br>40<br>20<br>30<br>-30 -25 -10 0 15 30 50 60 70 (HORIZONTAL) 90 100 115 180 264<br>AMBIENT TEMPERATURE ( ℃ ) INPUT VOLTAGE (VAC) 60Hz<br>LOAD (%) LOAD (%)<br>**----- End of picture text -----**<br>


_File Name:RPB-1600-SPEC   2019-09-25_ 

**- RPB 1600 series** 

## 1600W Intelligent Single Output Battery Charger 

## **Function Manual** 

## **1.PMBus Communication Interface** 

- ※ RPB-1600 supports PMBus Rev. 1.1 with maximum 100KHz bus speed, allowing information reading, status monitoring, output trimming, etc. For details, please refer to the Installation Manual. 

## **2.Charging Curve** 

- ※ By factory default, this charger performs the default curve which can be programmed via PMBus and CANBus. PIN10 and PIN14 on CN1 are thus shorted by default. 

- ※ To disable/ enable the charging curve, change to a 2 stage curve, a different curve frequently used for certain types of batteries in the industry, switch to PMBus, CANBus, PV/PC or SVR control instead and so on, please refer to the Installation Manual. 

**==> picture [477 x 270] intentionally omitted <==**

**----- Start of picture text -----**<br>
※ To program the parameters of the charging curve, SBP-001, the smart battery charging programmer designed by MEAN WELL, and a personal<br>computer are needed. Please contact MEAN WELL for details.<br>◎ Default 3 stage charging curve ◎ Embedded 3 stage charging curve<br>3 Stage MODEL Description Vboost Vfloat CC (default)<br>Start Default, programmable 14.4 13.8<br>Vboost<br>Vfloat 12V Pre-defined, gel battery 14 13.6 100A<br>Charge Voltage Pre-defined, flooded battery 14.2 13.4<br>Pre-defined, AGM battery 14.5 13.5<br>100% CC Default, programmable 28.8 27.6<br>Pre-defined, gel battery 28 27.2<br>24V 55A<br>Charge Current Constant Current Constant Voltage Float 10% CC Pre-defined, flooded battery 28.4 26.8<br>Pre-defined, AGM battery 29 27<br>stage 1 stage 2 stage 3 Default, programmable 57.6 55.2<br>Color of  LED Orange Green Pre-defined, gel battery 56 54.4<br>48V 27.5A<br>Status Indicator Charger fail if charging time Pre-defined, flooded battery 56.8 53.6<br>exceed charging timeout<br>Pre-defined, AGM battery 58 54<br>◎ Suitable for lead-acid batteries (flooded, Gel and AGM) and<br>Li-ion batteries (lithium iron and lithium manganese).<br>3. Front Panel LED Indicators & Corresponding Signal at Function Pins<br>LED Description<br>Green Float (stage 3)<br>Orange Charging (stage 1 or stage 2)<br>Red Abnormal status (OTP, OLP, Fan Fail, Charging timeout.)<br>**----- End of picture text -----**<br>


**3. Front Panel LED Indicators & Corresponding Signal at Function Pins** 

**4. Output Voltage Programming (or, PV / remote voltage programming / remote adjust / margin programming / dynamic voltage trim)** ※ In addition to the adjustment via the built-in potentiometer, the output voltage can be trimmed by applying EXTERNAL VOLTAGE. 

**==> picture [243 x 220] intentionally omitted <==**

**----- Start of picture text -----**<br>
PIN12 PV PIN14 -V-signal<br>-V CN1 +V<br>EXTERNAL VOLTAGE (DC)<br>RPB-1600-48 RPB-1600-24 RPB-1600-12<br>60 30 15<br>Non-Linear<br>48 24 12<br>36 18 9<br>V<br>0 0 0 0.4 1 4.7 5<br>EXTERNAL VOLTAGE (DC)<br>OUTPUT  VOLTAGE(V)<br>**----- End of picture text -----**<br>


_File Name:RPB-1600-SPEC   2019-09-25_ 

**- RPB 1600 series** 

1600W Intelligent Single Output Battery Charger 

## **5. Output Current Programming (or, PC / remote current programming / dynamic current trim)** 

※ The output current can be trimmed to 20~100% of the rated current by applying EXTERNAL VOLTAGE. 

**==> picture [426 x 284] intentionally omitted <==**

**----- Start of picture text -----**<br>
Iout<br>100<br>Non-Linear<br>PIN11 PC PIN14 -V-signal<br>-V CN1 +V<br>EXTERNAL VOLTAGE (DC)<br>20<br>V<br>0.4 1 4.7 5<br>EXTERNAL VOLTAGE (VDC)<br>The power supply can be turned ON/OFF individually or along with other units in parallel by using the "Remote ON-OFF" function.<br>PIN3 +5V-AUX switch Between Remote ON-OFF and +5V-AUX Power Supply Status<br>Switch Short ON<br>Switch Open OFF<br>PIN4 Remote  ON-OFF<br>OUTPUT CURRENT (%)<br>**----- End of picture text -----**<br>


## **6. Remote ON-OFF Control** 

The power supply can be turned ON/OFF individually or along with other units in parallel by using the "Remote ON-OFF" function. 

**==> picture [205 x 50] intentionally omitted <==**

**----- Start of picture text -----**<br>
PIN3 +5V-AUX switch<br>PIN4 Remote  ON-OFF<br>-V CN1 +V<br>**----- End of picture text -----**<br>


## **7.Temperature Compensation** 

- _PIN15 RTH+_ ◎ To exploit the temperature compensation function, please attach NTC the temperature sensor, NTC, which is enclosed with the charger, to the battery or the battery's vicinity. 

- _PIN16 RTH-_ ◎ The charger is able to work normally without the NTC. 

**==> picture [444 x 186] intentionally omitted <==**

**----- Start of picture text -----**<br>
PIN15 RTH+ ◎ To exploit the temperature compensation function, please attach<br>NTC the temperature sensor, NTC, which is enclosed with the charger,<br>to the battery or the battery's vicinity.<br>PIN16 RTH- ◎ The charger is able to work normally without the NTC.<br>-V CN1 +V<br>15 When multiple chargers are connected in parallel, please configure with the NTC<br>Unit 1 NTC as exhibited in the diagram .<br>16 If the temperature compensation is not required, RTH+ (PIN15) and RTH- (PIN16)<br>from each unit still need to be connected.<br>15<br>Unit 2<br>16<br>15<br>Unit 3<br>16<br>**----- End of picture text -----**<br>


## **8. Alarm Signal Output** 

- ※ There are 2 alarm signals, DC OK and T-ALARM, in TTL signal form, on CN1. These signals are isolated from output. The maximum sink current is 10mA. 

**==> picture [293 x 64] intentionally omitted <==**

**----- Start of picture text -----**<br>
PIN5 DC OK<br>Application<br>Circuit<br>PIN6 T-ALARM<br>-V CN1 +V PIN2 GND-AUX<br>**----- End of picture text -----**<br>


_File Name:RPB-1600-SPEC   2019-09-25_ 

**- RPB 1600 series** 

1600W Intelligent Single Output Battery Charger 

- **9.Current Sharing with Remote Sensing** RPB-1600 has the built-in active current sharing function and can be connected in parallel, up to 3 units, to provide higher output power as exhibited below : ※ The power supplies should be paralleled using short and large diameter wiring and then connected to the load. ※ Difference of output voltages among parallel units should be less than 0.2V. 

- ※ The total output current must not exceed the value determined  by the following equation: Maximum output current at parallel operation=(Rated current per unit)×(Number of unit)×0.9 

- ※ When the total output current is less than 5% of the total rated current, or say (5% of Rated current per unit)×(Number of unit) the current shared among units may not be balanced. 

|Parallel<br>1 unit<br>2 unit<br>3 unit<br>※CN500/SW1 Function pin connection|Parallel<br>1 unit<br>2 unit<br>3 unit<br>※CN500/SW1 Function pin connection|||||||
|---|---|---|---|---|---|---|---|
||arallel|PSU1||PSU2||PSU3||
|||CN500|SW1|CN500|SW1|CN500|SW1|
||1 unit|X|ON|∣|∣|∣|∣|
||2 unit|V|ON|V|ON|∣|∣|
||3 unit|V|ON|V|OFF|V|ON|



(V : CN500 connected ; X : CN500 not connected.) 

**==> picture [269 x 286] intentionally omitted <==**

**----- Start of picture text -----**<br>
RPB-1600 RPB-1600 RPB-1600<br>PSU1 PSU2 PSU3<br>-V -V -V<br>+V TB1 +V TB1 +V TB1<br>-V +V<br>LOAD<br>Fig 5.1<br>1 3 5 1 3 5 1 3 5<br>DA DB -V(signal) DA DB -V(signal) DA DB -V(signal)<br>DA DB -V(signal) DA DB -V(signal) DA DB -V(signal)<br>2 4 6 2 4 6 2 4 6<br>PSU1  CN500<br>PSU2  CN500 PSU3  CN500<br>If the lines of CN500 are too long, they should<br>be twisted in pairs to avoid the noise.<br>**----- End of picture text -----**<br>


◎ DA,DB and -V(signal) are connected mutually in parallel. 

_File Name:RPB-1600-SPEC   2019-09-25_ 

**- RPB 1600 series** 

1600W Intelligent Single Output Battery Charger 

## **Mechanical Specification** 

**==> picture [468 x 732] intentionally omitted <==**

**----- Start of picture text -----**<br>
Case No.250         Unit:mm<br>30 5.8 252<br>2-M4  L=5<br>20<br>28 2 2<br>-V<br>38<br>+V<br>Air flow<br>LED SW1 SVR (TOP View) direction<br>1<br>I/P 2<br>3<br>2 2<br>2-M4  L=5<br>2-M3<br>12 max.<br>5.8 252<br>300<br>1 1<br>(Bottom View)<br>3-M3 L=4<br>1<br>16.1 264.7<br>Chassis of RPB-1600<br>※ Mounting Instruction Mounting Surface<br>Hole No. Recommended Screw Size MAX. Penetration Depth  L Recommended mounting torque<br>1 M3 6mm 6~8Kgf-cm<br>2 M4 7mm 7~10Kgf-cm<br>Mounting Screw<br>※Control Pin No. Assignment(CN1) : HRS DF11-16DP-2DS or equivalent<br>1 15<br>Mating Housing HRS DF11-16DS or equivalent<br>Terminal HRS DF11-**SC or equivalent<br>2 16<br>Pin No. Function Description<br>1 +12V-AUX Auxiliary voltage output, 10.6~13.2V, referenced to GND-AUX (pin2).<br>The maximum load current is 0.8A. This output has the built-in "Oring diodes" and is not controlled by “Remote ON-OFF”.<br>2 GND-AUX Auxiliary voltage output GND.<br>The signal return is isolated from the output terminals (+V & -V).<br>3 +5V-AUX Auxiliary voltage output, 4.5~5.5V, referenced to GND-AUX (pin2).<br>The maximum load current is 0.3A. This output has the built-in "Oring diodes" and is not controlled by “Remote ON-OFF<br>4 Remote The unit can turn the output ON/OFF by electrical signal or dry contact between Remote ON/OFF and +5V-AUX . (Note.2)<br>ON-OFF Short (4.5 ~ 5.5V) : Power ON ; Open (0 ~ 0.5V) : Power OFF ; The maximum input voltage is 5.5V.<br>High (4.5 ~ 5.5V) : When the Vout ≦8V/16V/32V ±1V.<br>5 DC-OK Low (-0.1 ~ 0.5V) : When Vout ≧8V/16V/32V ±1V. The maximum sourcing current is 10mA and only for output. (Note.2)<br>DC OK  is associated with battery low protection.<br>High (4.5 ~ 5.5V) : When the internal temperature exceeds the limit of temperature alarm, or when Fan fails.<br>6 T-ALARM Low (-0.1 ~ 0.5V) : When the internal temperature is normal, and when Fan normally works.<br>The maximum sourcing current is 10mA and only for output(Note.2)<br>7,8,9 A0,A1,A2 PMBus / CANBus interface address lines. (Note.1)<br>10 D0 Charging mechanism control. This pin determines, for charging operation, whether charging curve is used, or control over<br>PMBus, PV/PC or SVR is used. Please refer to the installation Manual. (Note.1)<br>11 PC Connection for output current programming. (Note.1)<br>12 PV Connection for output voltage programming. (Note.1)<br>13 +V (Signal) Positive output voltage signal.<br>It cannot be connected directly to the load.<br>14 -V (Signal) Negative output voltage signal.<br>It is for certain function reference; it cannot be connected directly to the load.<br>15 RTH+ Temperature sensor(NTC, 5KOhm) comes along with the charger can be connected to the unit to allow temperature<br>16 RTH- compensation of the charging voltage.<br>Note1: Non-isolated signal, referenced to the [-V(signal)].<br>Note2: Isolated signal, referenced to GND-AUX.<br>ψ<br>6.5<br>7.5<br>9<br>21.6 22.8<br>29.6<br>2<br>85<br>10<br>13 41<br>22.8<br>70<br>42.5<br>2 1<br>CN1<br>16 15 1 7<br>2 8<br>CN500<br>**----- End of picture text -----**<br>


_File Name:RPB-1600-SPEC 2019-09-25_ 

**- RPB 1600 series** 

## 1600W Intelligent Single Output Battery Charger 

※AC Input Terminal Pin No. Assignment Pin No. Assignment Diagram Maximum mounting torque 1 FG 2 AC/N 8Kgf-cm 3 AC/L ※Control Pin No. Assignment(CN500) : HRS DF11-8DP-2DS or equivalent 1 7 Mating Housing HRS DF11-8DS or equivalent Terminal HRS DF11-**SC or equivalent 2 8 **Pin No. Function Description** 1,2 DA Differential digital signal for parallel control. (Note.1) 3,4 DB Differential digital signal for parallel control. (Note.1) Negative output voltage signal. 5,6 -V (Signal) It is for certain function reference; it cannot be connected directly to the load. SDA For PMBus model: Serial Data used in the PMBus interface. (Note.2) 7 CANH For CANBus model: Data line used in CANBus interface. (Note.2) SCL For PMBus model: Serial Clock used in the PMBus interface. (Note.2) 8 CANL For CANBus model: Data line used in CANBus interface. (Note.2) 

Note1: Non-isolated signal, referenced to [-V(signal)]. Note2: Isolated signal, referenced to GND-AUX. 

※Control Pin No. Assignment(SW1) 

**Pin No. Function Description** Terminal 1,2 resistance SW1 is the selector of terminal resistor that is designed for DA/DB signals and parallel control function. 

_File Name:RPB-1600-SPEC   2019-09-25_