OKL2-T/20-W12N2-C

## **www.murata-ps.com** 

## **- - OKL2 T/20 W12 Series** 

Programmable Output 20-Amp **i** LGA SMT PoL DC-DC Converter Series 

**==> picture [38 x 8] intentionally omitted <==**

**----- Start of picture text -----**<br>
Typical unit<br>**----- End of picture text -----**<br>


## **FEATURES** 

- **i** LGA inspectable Land Grid Array 

- 4.5-14Vdc input voltage range 

- Programmable output voltage from 0.69-5.5Vdc 

- Drives 1000μF ceramic capacitive loads 

- High power conversion effi ciency at 94% 

- Outstanding thermal derating performance 

- Over temperature and over current protection 

## **PRODUCT OVERVIEW** 

The OKL2-T/20-W12 series are non-isolated point-of-Load (PoL) DC-DC power converters for embedded applications. The tiny form factor is confi gured on a Land Grid Array (LGA) assembly measuring only 1.3 x 0.53 x0.34 inches (33.02 x 13.46 x 8.75 mm). Applications include powering CPUs, datacom/telecom systems, distributed bus architectures (DBA), programmable logic and mixed voltage systems. 

The wide input range is 4.5 to 14Volts DC. The maximum output current is 20Amps. Based on fi xed-frequency synchronous buck converter switching topology, the high power conversion effi cient Point of Load (PoL) module features programmable output voltage and On/Off control. 

These converters also include under voltage lock out (UVLO), output short circuit protection, overcurrent and over temperature protections. 

- On/Off control and Power Good output 

- RoHS-6 hazardous substance compliance 

- Tracking operation/Synchronized function 

**==> picture [401 x 297] intentionally omitted <==**

**----- Start of picture text -----**<br>
Connection Diagram<br>+Vin +Vout<br>F1<br>On/Off<br>b Control — ° Switching |<br>° Controller e Current Sense |<br>External<br>Trim<br>DC<br>Power b Open = On _— Reference and<br>Source Closed = Off Error Amplifier<br>(Positive<br>On/Off)<br>|<br>O 7 | RTrim<br>Common | Common<br>Sequence/Tracking o SP [nn] O Power Good O<br>Sync<br>Figure 1. OKL2-T/20-W12<br>Note: Murata Power Solutions strongly recommends an external input fuse, F1.<br>See specifi cations.<br>£25)<br>For full details go to<br>www.murata-ps.com/rohs Oy]<br>**----- End of picture text -----**<br>


**www.murata-ps.com/support** 

**MDC_OKL2-T20-W12.B02** Page 1 of 19 

## **- - OKL2 T/20 W12 Series** 

Programmable Output 20-Amp **i** LGA SMT PoL DC-DC Converter Series 

|**PERFORMANCE SPECIFICATIONS SUMMARY AND ORDERING GUIDE**|**PERFORMANCE SPECIFICATIONS SUMMARY AND ORDERING GUIDE**|**PERFORMANCE SPECIFICATIONS SUMMARY AND ORDERING GUIDE**|**PERFORMANCE SPECIFICATIONS SUMMARY AND ORDERING GUIDE**|**PERFORMANCE SPECIFICATIONS SUMMARY AND ORDERING GUIDE**|**PERFORMANCE SPECIFICATIONS SUMMARY AND ORDERING GUIDE**|**PERFORMANCE SPECIFICATIONS SUMMARY AND ORDERING GUIDE**|**PERFORMANCE SPECIFICATIONS SUMMARY AND ORDERING GUIDE**||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|**Model Number**||Output||||||Input|||Eff ciency (%)||On/<br>Off<br>Logic|Dimensions|
||Vout<br>(Volts)➀|Iout (Amps,<br>max.)➁|Power<br>(Watts)|R/N<br>(mV p-p)<br>Max.➃|Regulation (max.)||Vin nom.<br>(Volts)|Range<br>(Volts)➃|Iin, no load<br>(mA)➃|Iin, full load<br>(Amps)➁||||Inches (mm)|
||||||Line|Load|||||Min.|Typ.|||
|**OKL2-T/20-W12P2-C**|0.69-5.5|20|100|35|±0.4%|±0.3%|12|4.5-14|75|8.87|91.0|94.0|Pos.|1.3 x 0.53 x 0.34<br>(33.02 x 13.46 x 8.75)|
|**OKL2-T/20-W12N2-C**|||||||||||||Neg.||



➀ The output range is limited by Vin. See detailed specs. ➂ Use adequate ground plane and copper thickness adjacent to the converter. 

- ➁ All specifi cations are at nominal line voltage, Vout=nominal (5V) and full  Ripple and Noise (R/N) and no-load input current are shown at Vout=1.8V. load, +25°C. unless otherwise noted. See specs for details. 

   - Output capacitors are 188 μF ceramic. Input cap is 44 μF. See tailed specifi cations. I/O caps are necessary for our test equipment and may not be needed for your application. 

**==> picture [543 x 190] intentionally omitted <==**

**----- Start of picture text -----**<br>
PART NUMBER STRUCTURE<br>OK L 2 - T / 20 - W12 N2 - C<br>Okami Non-isolated PoL<br>iLGA Surface Mount, MSL Rating 2<br>Sequence/tracking RoHS Hazardous<br>Blank = Not Installed Substance Compliance<br>2 = installed C = RoHS-6 (does not claim EU RoHS exemption<br>Trimmable Output  7b – lead in solder)<br>Voltage Range On/Off Logic<br>0.69-5.5Vdc P2 = Positive Logic<br>N2 = Negative Logic<br>Maximum Rated Output Input Voltage Range<br>Current in Amps 4.5-14Vdc<br>**----- End of picture text -----**<br>


## **Product Label** 

Because of the small size of these products,  the product label contains a character-reduced code to indicate the model number and manufacturing date code. Not all items on the label are always used. Please note that the label differs from the product photograph. Here is the layout of the label: 

|**Model Number**|**Product Code**|
|---|---|
|OKL2-T/20-W12P2-C|L21120|
|OKL2-T/20-W12N2-C|L20120|



The manufacturing date code is four characters: 

XXXXXX Product code Mfg. date YMDX   Rev. Revision level code 

Figure 2. Label Artwork Layout 

First character – Last digit of manufacturing year, example 200 **9** Second character – Month code (1 through 9 = Jan-Sep; O, N, D = Oct, Nov, Dec) 

Third character – Day code (1 through 9 = 1 to 9, 10 = 0 and 11 through 31 = A through Z) Fourth character – Manufacturing information 

The label contains two rows of information: 

First row – Model number product code (see table) Second row – Manufacturing date code and revision level 

**www.murata-ps.com/support** 

**MDC_OKL2-T20-W12.B02** Page 2 of 19 

## **- - OKL2 T/20 W12 Series** 

Programmable Output 20-Amp **i** LGA SMT PoL DC-DC Converter Series 

## **FUNCTIONAL SPECIFICATIONS** 

**==> picture [542 x 612] intentionally omitted <==**

**----- Start of picture text -----**<br>
ABSOLUTE MAXIMUM RATINGS Conditions (1) Minimum Typical/Nominal Maximum Units<br>Input Voltage, Continuous Full power operation 0 15 Vdc<br>Output Power 0 110 W<br>Current-limited, no damage,<br>Output Current 0 20 A<br>short-circuit protected<br>On/Off Control 14 Vdc<br>Power Good Pin 6 Vdc<br>Synchronized Pin 12 Vdc<br>Sequence Pin Vin max Vdc<br>Storage Temperature Range Vin = Zero (no power) -55 125 ˚C<br>Absolute maximums are stress ratings. Exposure of devices to greater than any of these conditions may adversely affect long-term reliability. Proper operation under conditions other<br>than those listed in the Performance/Functional Specifi cations Table is not implied or recommended.<br>INPUT<br>Operating voltage range (7) See output voltage vs input voltage 4.5 12 14 Vdc<br>Recommended External Fuse Fast blow 36 A<br>Turn On/Start-up threshold  Rising input voltage 3.9 4.2 4.5 Vdc<br>Undervoltage Shutdown 3.7 4 4.3<br>Internal Filter Type C-TYPE<br>Input current<br>Full Load Conditions Vin = nominal (5Vo set) 8.87 9.29 A<br>Low Line Vin @ min, 5 Vout 15.12 15.85 A<br>Inrush Transient TBD A [2] -Sec.<br>Short Circuit Input Current TBD mA<br>No Load Input Current 5Vout, Iout @ 0 75 150 mA<br>No Load Input Current 1V, Iout @ 0 35 70<br>Shut-Down Mode Input Current 1 mA<br>Refl ected (back) ripple current (2) Measured at input with specifi ed fi lter TBD mA, pk-pk<br>GENERAL and SAFETY<br>@ Vin nom, 5Vout 91 94<br>@ Vin min=8Vin, 5Vout 91.5 94.5<br>EFFICIENCY (12Vin @ 12A load current) @ Vin nom, 3.3Vout 89 92 %<br>@ Vin nom, 2.5Vout 90<br>@Vin nom, 1.8Vout 83.5 88<br>Certifi ed to UL-60950-1, CSA-C22.2<br>Safety No.60950-1, IEC/60950-1, 2nd edition  Yes<br>(pending)<br>Per Telcordia SR332, issue 1 class 3, ground<br>Calculated MTBF (4a) 8,068,510 Hours<br>fi xed, Tambient=+25˚C<br>Calculated MTBF (4b) Per Mil-HDBK-217N2 Method 4,514,048 Hours<br>DYNAMIC CHARACTERISTICS<br>Fixed Switching Frequency 400 KHz<br>Synchronization frequency range 420 600 KHz<br>High level input voltage 3 12 Vdc<br>Low level input voltage 0 0.8 Vdc<br>Input currrent SYNC pin VSYNC = 3.0V 1 mA<br>Minimun pulse width, SYNC 250 nS<br>Minimum pulse set-up/hold time SYNC pin (note 15) 250 nS<br>Startup Time Power On to Vout regulated 6 mS<br>Startup Time Remote ON to to Vout regulated 6 mS<br>50-100-50% load step, settling time to within<br>Dynamic Load Response 100 μSec<br>±2% of Vout di/dt =1 A/μSec<br>Dynamic Load Peak Deviation same as above ±200 mV<br>FEATURES and OPTIONS<br>Remote On/Off Control (5)<br>“N” suffi x<br>Negative Logic, ON state Pin open=ON 0 0.7 V<br>Negative Logic, OFF state 2 +Vin-max V<br>Control Current open collector/drain 3 mA<br>“P” suffi x<br>Positive Logic, ON state Pin open=ON +Vin-0.8V Vin-max V<br>Positive Logic, OFF state 0 2.5 V<br>Control Current open collector/drain 3 mA<br>Remote Sense 500 mV<br>**----- End of picture text -----**<br>


**www.murata-ps.com/support** 

**MDC_OKL2-T20-W12.B02** Page 3 of 19 

## **- - OKL2 T/20 W12 Series** 

Programmable Output 20-Amp **i** LGA SMT PoL DC-DC Converter Series 

## **FUNCTIONAL SPECIFICATIONS (CONT.)** 

**==> picture [542 x 456] intentionally omitted <==**

**----- Start of picture text -----**<br>
FEATURES and OPTIONS, CONT. Conditions (1) Minimum Typical/Nominal Maximum Units<br>Tracking/Sequencing(optional)<br>Slew Rate TBD V/mS<br>Tracking Accuracy Rising input (0.5V/ms) TBD mV<br>Tracking Accuracy Falling input(0.5V/ms) TBD mV<br>Power Good Option<br>PGOOD, Open Drain Confi guration, Sinking:<br>Vout window for PGOOD: True -10% 10% Vset<br>Vout window for PGOOD: False 0.05 Vdc<br>OUTPUT<br>Total Output Power 0 100 110 W<br>Voltage<br>Nominal Output Voltage Range (13) See trim formula 0.69 5.5 Vdc<br>Setting Accuracy At 50% load -1.5 1.5 % of Vnom.<br>Output Voltage Overshoot-Startup 3 % Vo set<br>Current<br>Output Current Range 0 20 20 A<br>Minimum Load No minimum load<br>Current Limit Inception (6) 98% of Vnom., after warmup  20.2 32 A<br>Short Circuit<br>Hiccup technique, autorecovery within ±1%<br>Short Circuit Current (17) 0.02 A<br>of Vout<br>Short Circuit Duration (remove short for<br>Output shorted to ground, no damage Continuous<br>recovery)<br>Short circuit protection method Current limiting<br>Regulation (10)<br>Total Regulation Band -2.5 Vo set 2.5 % Vo set<br>Line Regulation Vin=min. to max. Vout=nom. ±0.4 %<br>Load Regulation Iout=min. to max. ±0.3 %<br>5Vo, 12Vin 45 100<br>3.3Vo, 12Vin 35 80<br>Ripple and Noise (8) mV pk-pk<br>1.8Vo, 12Vin 35 80<br>0.69Vo, 7Vin 30 70<br>Temperature Coeffi cient At all outputs ±0.02 % of Vnom./°C<br>Low ESR; >0.001, <0.01 ohm 188 1000<br>Maximum Capacitive Loading (14) μF<br>ESR > 0.01 ohm 10000<br>MECHANICAL<br>Outline Dimensions 1.3 x 0.53 x 0.34 Inches<br>33.02 x 13.46 x 8.75 mm<br>Weight 0.2 Ounces<br>5.4 Grams<br>ENVIRONMENTAL<br>full power, all output voltages, see derating<br>Operating Ambient Temperature Range (9) -40 85 ˚C<br>curves<br>Storage Temperature Vin = Zero (no power) -55 125 ˚C<br>Thermal Protection/Shutdown Measured in center TBD ˚C<br>RoHS rating RoHS-6<br>**----- End of picture text -----**<br>


## **Notes** 

- (1) Specifi cations are typical at +25 °C, Vin = nominal (+12V), Vout = nominal (+5V), full load, external caps and natural convection unless otherwise indicated. Extended tests at full power must supply substantial forced airfl ow. All models are tested and specifi ed with external 188μF ceramic output capacitors and a 44 μF external input capacitor. All capacitors are low ESR types. These capacitors are necessary to accommodate our test equipment and may not be required to achieve specifi ed performance in your applications. However, Murata Power Solutions recommends installation of these capacitors. All models are stable and regulate within spec under no-load conditions. 

- (2) Input Back Ripple Current is tested and specifi ed over a 5 Hz to 20 MHz bandwidth. Input fi ltering is Cin = 2 x 100 μF ceramic, Cbus = 1000 μF electrolytic, Lbus = 1 μH. 

- (3) Note that Maximum Power Derating curves indicate an average current at nominal input voltage. At higher temperatures and/or lower airfl ow, the DC-DC converter will tolerate brief full current outputs if the total RMS current over time does not exceed the Derating curve. 

- (4a) Mean Time Before Failure is calculated using the Telcordia (Belcore) SR-332 Method 1, Case 3, ground fi xed conditions, Tpcboard = +25 ˚C, full output load, natural air convection. 

- (4b) Mean Time Before Failure is calculated using the MIL-HDBK-217N2 method, ground benign, +25oC., full output load, natural convection. 

- (5) The On/Off Control Input should use either a switch or an open collector/open drain transistor referenced to -Input Common. A logic gate may also be used by applying appropriate external voltages which do not exceed +Vin. 

- (6) Short circuit shutdown begins when the output voltage degrades approximately 2% from the selected setting. 

- (7) Please observe the voltage input and output specifi cations in the voltage range graph. 

- (8) Output noise may be further reduced by adding an external fi lter. At zero output current, the output may contain low frequency components which exceed the ripple specifi cation. The output may be operated indefi nitely with no load. 

- (9) All models are fully operational and meet published specifi cations, including “cold start” at –40˚ C. 

- (10) Regulation specifi cations describe the deviation as the line input voltage or output load current is varied from a nominal midpoint value to either extreme. 

**www.murata-ps.com/support** 

**MDC_OKL2-T20-W12.B02** Page 4 of 19 

## **- - OKL2 T/20 W12 Series** 

## Programmable Output 20-Amp **i** LGA SMT PoL DC-DC Converter Series 

## **Notes, cont.** 

- (11) Other input or output voltage ranges will be reviewed under scheduled quantity special order. 

- (12) Maximum PC board temperature is measured with the sensor in the center of the converter. 

- (13) Do not exceed maximum power specifi cations when adjusting the output trim. 

- (14) The maximum output capacitive loads depend on the the Equivalent Series Resistance (ESR) of the external output capacitor and, to a lesser extent, the distance and series impedance to the load. Larger caps will reduce output noise but may change the transient response. Newer ceramic caps with very low ESR may require lower capacitor values to avoid instability. Thoroughly test your capacitors in the application. Please refer to the Output Capacitive Load Technical Note. 

- (15) Do not allow the input voltage to degrade lower than the input undervoltage shutdown voltage at all times. Otherwise, you risk having the converter turn off. The undervoltage shutdown is not latching and will attempt to recover when the input is brought back into normal operating range. 

- (16) The outputs are not intended to sink appreciable reverse current. 

- (17) “Hiccup” overcurrent operation repeatedly attempts to restart the converter with a brief, full-current output. If the overcurrent condition still exists, the restart current will be removed and then tried again. This short current pulse prevents overheating and damaging the converter. Once the fault is removed, the converter immediately recovers normal operation. 

**www.murata-ps.com/support** 

**MDC_OKL2-T20-W12.B02** Page 5 of 19 

## **- - OKL2 T/20 W12 Series** 

## Programmable Output 20-Amp **i** LGA SMT PoL DC-DC Converter Series 

**==> picture [234 x 8] intentionally omitted <==**

**----- Start of picture text -----**<br>
OKL2-T/20-W12 PERFORMANCE DATA AND OSCILLOGRAMS<br>**----- End of picture text -----**<br>


**==> picture [248 x 185] intentionally omitted <==**

**----- Start of picture text -----**<br>
Effi ciency vs. Line Voltage and Load Current @Ta = +25 °C (Vout = 5V)<br>100<br>95 SS—— ———<br>= VIN = 8V<br>VIN = 12V<br>90<br>VIN = 14V<br>85<br>80<br>75<br>0 4 8 12 16 20<br>Load Current (Amps)<br>Efficiency (%)<br>**----- End of picture text -----**<br>


On/Off Enable Delay (Vin=12V, Vout=5.0V, Iout=20A, Cload=188μF) Trace2=Enable, 5V/div Trace1=Vout,2V/div 

Step Load Transient Response (Vin=12V, Vout=5.0V, Cload=188μF, Iout=10A to 20A) Trace 1=Vout, 100 mV/div(AC), Trace 4=Iout, 10A/div. 

**==> picture [250 x 176] intentionally omitted <==**

**----- Start of picture text -----**<br>
Maximum Current Temperature Derating at Sea Level (Vin=12V, Vout=5.0V)<br>22<br>20<br>18 ——__<br>161412 ||SSS|> Natural Convection 0.5 m/s (100 LFM) |—o~SSoS<br>1.0 m/s (200 LFM) wa<br>10<br>8<br>6<br>4<br>2<br>0<br>10 20 30 40 50 60 70 80 90<br>Ambient Temperature (°C)<br>Output Current (Amps)<br>**----- End of picture text -----**<br>


Output Ripple and Noise (Vin=12V, Vout=5.0V, Iout=20A, Cload=188μF, ScopeBW=20MHz) Trace1=Vout,10mV/div(AC) 

Step Load Transient Response (Vin=12V, Vout=5.0V, Cload=188μF, Iout=20A to 10A) Trace 1=Vout, 100 mV/div(AC), Trace 4=Iout, 10A/div. 

**www.murata-ps.com/support** 

**MDC_OKL2-T20-W12.B02** Page 6 of 19 

## **- - OKL2 T/20 W12 Series** 

## Programmable Output 20-Amp **i** LGA SMT PoL DC-DC Converter Series 

## **OKL2-T/20-W12 PERFORMANCE DATA AND OSCILLOGRAMS** 

**==> picture [519 x 185] intentionally omitted <==**

**----- Start of picture text -----**<br>
Effi ciency vs. Line Voltage and Load Current @Ta = +25 °C (Vout = 3.3V) Maximum Current Temperature Derating at Sea Level (Vin=12V, Vout=3.3V)<br>100<br>22<br>95 a 20 —=<br>18<br>> ——————__——— VIN = 4.5V 16 oSa<br>90 jja~~ VIN = 12V — 14 SSES ——eee<br>VIN = 14V 12 Natural Convection0.5 m/s (100 LFM)<br>10 || 1.0 m/s (200 LFM) “oS<br>85<br>8<br>6<br>80 4<br>2<br>0<br>75 20 30 40 50 60 70 80 90<br>0 4 8 12 16 20<br>Ambient Temperature (°C)<br>Load Current (Amps)<br>Efficiency (%) Output Current (Amps)<br>**----- End of picture text -----**<br>


On/Off Enable Delay (Vin=12V, Vout=3.3V, Iout=20A, Cload=188μF) Trace2=Enable, 5V/div Trace1=Vout,1V/div 

**==> picture [211 x 18] intentionally omitted <==**

**----- Start of picture text -----**<br>
Output Ripple and Noise (Vin=12V, Vout=3.3V, Iout=20A, Cload=188μF,<br>ScopeBW=20MHz) Trace1=Vout,10mV/div(AC)<br>**----- End of picture text -----**<br>


Step Load Transient Response (Vin=12V, Vout=3.3V, Cload=188μF, Iout=10A to 20A) Trace 1=Vout, 100 mV/div(AC), Trace 4=Iout, 10A/div. 

Step Load Transient Response (Vin=12V, Vout=3.3V, Cload=188μF, Iout=20A to 10A) Trace 1=Vout, 100 mV/div(AC), Trace 4=Iout, 10A/div. 

**www.murata-ps.com/support** 

**MDC_OKL2-T20-W12.B02** Page 7 of 19 

## **- - OKL2 T/20 W12 Series** 

## Programmable Output 20-Amp **i** LGA SMT PoL DC-DC Converter Series 

**==> picture [234 x 8] intentionally omitted <==**

**----- Start of picture text -----**<br>
OKL2-T/20-W12 PERFORMANCE DATA AND OSCILLOGRAMS<br>**----- End of picture text -----**<br>


**==> picture [248 x 185] intentionally omitted <==**

**----- Start of picture text -----**<br>
Effi ciency vs. Line Voltage and Load Current @Ta = +25 °C (Vout = 2.5V)<br>100<br>95 — —___<br>90<br>~ VVININ = 4.5V = 12V<br>VIN = 14V<br>85<br>80<br>75<br>0 4 8 12 16 20<br>Load Current (Amps)<br>Efficiency (%)<br>**----- End of picture text -----**<br>


On/Off Enable Delay (Vin=12V, Vout=2.5V, Iout=20A, Cload=188μF) Trace2=Enable, 5V/div Trace1=Vout,1V/div 

Step Load Transient Response (Vin=12V, Vout=2.5V, Cload=188μF, Iout=10A to 20A) Trace 1=Vout, 100 mV/div(AC), Trace 4=Iout, 10A/div. 

**==> picture [250 x 175] intentionally omitted <==**

**----- Start of picture text -----**<br>
Maximum Current Temperature Derating at Sea Level (Vin=12V, Vout=2.5V)<br>22<br>20<br>18 oS eee<br>16<br>14<br>Natural Convection<br>1210 || 1.0 m/s (200 LFM) 0.5 m/s (100 LFM) <<eS~<br>8<br>6<br>4<br>2<br>0<br>20 30 40 50 60 70 80 90<br>Ambient Temperature (°C)<br>Output Current (Amps)<br>**----- End of picture text -----**<br>


**==> picture [211 x 18] intentionally omitted <==**

**----- Start of picture text -----**<br>
Output Ripple and Noise (Vin=12V, Vout=2.5V, Iout=20A, Cload=188μF,<br>ScopeBW=20MHz) Trace1=Vout,10mV/div(AC)<br>**----- End of picture text -----**<br>


Step Load Transient Response (Vin=12V, Vout=2.5V, Cload=188μF, Iout=20A to 10A) Trace 1=Vout, 100 mV/div(AC), Trace 4=Iout, 10A/div. 

**www.murata-ps.com/support** 

**MDC_OKL2-T20-W12.B02** Page 8 of 19 

## **- - OKL2 T/20 W12 Series** 

## Programmable Output 20-Amp **i** LGA SMT PoL DC-DC Converter Series 

## **OKL2-T/20-W12 PERFORMANCE DATA AND OSCILLOGRAMS** 

**==> picture [248 x 185] intentionally omitted <==**

**----- Start of picture text -----**<br>
Effi ciency vs. Line Voltage and Load Current @Ta = +25 °C (Vout = 1.8V)<br>100<br>95 —__<br>90 \ ——<$<—~~<br>== —=—<br>VIN = 4.5V<br>85<br>VIN = 12V<br>VIN = 14V<br>80<br>75<br>0 4 8 12 16 20<br>Load Current (Amps)<br>Efficiency (%)<br>**----- End of picture text -----**<br>


On/Off Enable Delay (Vin=12V, Vout=1.8V, Iout=20A, Cload=188μF) Trace2=Enable, 5V/div Trace1=Vout,500mV/div 

Step Load Transient Response (Vin=12V, Vout=1.8V, Cload=188μF, Iout=10A to 20A) Trace 1=Vout, 100 mV/div(AC), Trace 4=Iout, 10A/div. 

**==> picture [250 x 175] intentionally omitted <==**

**----- Start of picture text -----**<br>
Maximum Current Temperature Derating at Sea Level (Vin=12V, Vout=1.8V)<br>22<br>20<br>18<br>a ———~<br>16<br>a SSERnr—=e<br>14 ee<br>Natural Convection<br>12 | | 0.5 m/s (100 LFM) — Se<br>10 1.0 m/s (200 LFM)<br>8<br>6<br>4<br>2<br>0<br>20 30 40 50 60 70 80 90<br>Ambient Temperature (°C)<br>Output Current (Amps)<br>**----- End of picture text -----**<br>


Output Ripple and Noise (Vin=12V, Vout=1.8V, Iout=20A, Cload=188μF, ScopeBW=20MHz) Trace1=Vout,10mV/div(AC) 

Step Load Transient Response (Vin=12V, Vout=1.8V, Cload=188μF, Iout=20A to 10A) Trace 1=Vout, 100 mV/div(AC), Trace 4=Iout, 10A/div. 

**www.murata-ps.com/support** 

**MDC_OKL2-T20-W12.B02** Page 9 of 19 

## **- - OKL2 T/20 W12 Series** 

## Programmable Output 20-Amp **i** LGA SMT PoL DC-DC Converter Series 

## **OKL2-T/20-W12 PERFORMANCE DATA AND OSCILLOGRAMS** 

**==> picture [248 x 184] intentionally omitted <==**

**----- Start of picture text -----**<br>
Effi ciency vs. Line Voltage and Load Current @Ta = +25 °C (Vout = 1.2V)<br>95<br>90 \ SS |<br>85 AS__—~~<br>VIN = 4.5V<br>80 VIN = 10.8V<br>VIN = 12V<br>75<br>70<br>0 4 8 12 16 20<br>Load Current (Amps)<br>Efficiency (%)<br>**----- End of picture text -----**<br>


On/Off Enable Delay (Vin=12V, Vout=1.2V, Iout=20A, Cload=188μF) Trace2=Enable, 5V/div Trace1=Vout,500mV/div 

Step Load Transient Response (Vin=12V, Vout=1.2V, Cload=188μF, Iout=10A to 20A) Trace 1=Vout, 100 mV/div(AC), Trace 4=Iout, 10A/div. 

**==> picture [250 x 176] intentionally omitted <==**

**----- Start of picture text -----**<br>
Maximum Current Temperature Derating at Sea Level (Vin=12V, Vout=1.2V)<br>22<br>20<br>18<br>16 SS .——=—__<br>14 |ee| Natural Convection SSSaar<br>12 0.5 m/s (100 LFM)<br>1.0 m/s (200 LFM)<br>10<br>8<br>6<br>4<br>2<br>0<br>20 30 40 50 60 70 80 90<br>Ambient Temperature (°C)<br>Output Current (Amps)<br>**----- End of picture text -----**<br>


Output Ripple and Noise (Vin=12V, Vout=1.2V, Iout=20A, Cload=188μF, ScopeBW=20MHz) Trace1=Vout,10mV/div(AC) 

Step Load Transient Response (Vin=12V, Vout=1.2V, Cload=188μF, Iout=20A to 10A) Trace 1=Vout, 100 mV/div(AC), Trace 4=Iout, 10A/div. 

**www.murata-ps.com/support** 

**MDC_OKL2-T20-W12.B02** Page 10 of 19 

## **- - OKL2 T/20 W12 Series** 

## Programmable Output 20-Amp **i** LGA SMT PoL DC-DC Converter Series 

## **OKL2-T/20-W12 PERFORMANCE DATA AND OSCILLOGRAMS** 

**==> picture [248 x 184] intentionally omitted <==**

**----- Start of picture text -----**<br>
Effi ciency vs. Line Voltage and Load Current @Ta = +25 °C (Vout = 0.69V)<br>95<br>90 —a<br>85 A\——— =<br>SS<br>80 VIN = 4.5V<br>VIN = 5V<br>VIN = 7V<br>75<br>70<br>0 4 8 12 16 20<br>Load Current (Amps)<br>Efficiency (%)<br>**----- End of picture text -----**<br>


On/Off Enable Delay (Vin=5.5V, Vout=0.69V, Iout=20A, Cload=188μF) Trace2=Enable, 5v/div, Trace1=Vout,200mV/div 

Step Load Transient Response (Vin=7V, Vout=0.69V, Cload=188μF, Iout=10A to 20A) Trace 1=Vout, 100 mV/div(AC), Trace 4=Iout, 10A/div. 

**==> picture [250 x 176] intentionally omitted <==**

**----- Start of picture text -----**<br>
Maximum Current Temperature Derating at Sea Level (Vin=7V, Vout=0.69V)<br>22<br>20<br>18<br>16 Jf| Oo SSL<br>14 ESS Natural Convection —=—=__ESE4 u<br>[| | ———SSa_<br>0.5 m/s (100 LFM)<br>12 1.0 m/s (200 LFM)<br>10<br>8<br>6<br>4<br>2<br>0<br>20 30 40 50 60 70 80 90<br>Ambient Temperature (°C)<br>Output Current (Amps)<br>**----- End of picture text -----**<br>


Output Ripple and Noise (Vin=7V, Vout=0.69V, Iout=20A, Cload=188μF, ScopeBW=20MHz) Trace1=Vout,10mV(AC) 

Step Load Transient Response (Vin=7V, Vout=0.69V, Cload=188μF, Iout=20A to 10A) Trace 1=Vout, 100 mV/div(AC), Trace 4=Iout, 10A/div. 

**www.murata-ps.com/support** 

**MDC_OKL2-T20-W12.B02** Page 11 of 19 

## **- - OKL2 T/20 W12 Series** 

Programmable Output 20-Amp **i** LGA SMT PoL DC-DC Converter Series 

## **MECHANICAL SPECIFICATIONS** 

**==> picture [486 x 598] intentionally omitted <==**

**----- Start of picture text -----**<br>
1 8 8 1<br>33.02<br>31.80<br>7<br>24.26<br>L＊＊＊＊＊ 7<br>①②③④<br>6 1.78×3.10×10PLACES<br>19.43<br>6<br>JU<br>9 5<br>14.60<br>5<br>9<br>4<br>|<br>9.78<br>4<br>=i 3 Figure 3. OKL2-T/20-W12 Mechanical Outline<br>4.95<br>3<br>1.90<br>Y<br>1<br>2<br>2 10 0<br>TOP VIEW Va X<br>0<br>BOTTOM  VIEW UNIT[mm]<br>[Tolerances ±0.25mm]<br>8.75<br>MAX<br>SIDE VIEW<br>INPUT/OUTPUT CONNECTIONS<br>[oo<br>Pin Function<br>1 On/Off Control*<br>2 VIN<br>3 Sequence/Tracking<br>4 Ground<br>5 VOUT<br>Dimensions are in inches (mm shown for ref. only).<br>6 Trim<br>7 +Sense (VOUT) ........_—~«d Third Angle Projection<br>8 -Sense (Ground)<br>9 Power Good Out<br>10 Syncronization<br>Tolerances (unless otherwise specified):<br>*The Remote On/Off can be provided with  .XX ± 0.02 (0.5)<br>either positive (P suffi x) or negative (N suffi x)  .XXX ± 0.010 (0.25)Angles ± 1˚Angles ± 1˚<br>logic.<br>5.46 11.55<br>1.52 6.73 12.19 13.46<br>**----- End of picture text -----**<br>


**==> picture [108 x 96] intentionally omitted <==**

**----- Start of picture text -----**<br>
Dimensions are in inches (mm shown for ref. only).<br>........_—~«d Third Angle Projection<br>Tolerances (unless otherwise specified):<br>.XX ± 0.02 (0.5)<br>.XXX ± 0.010 (0.25)Angles ± 1˚Angles ± 1˚<br>Components are shown for reference only.<br>**----- End of picture text -----**<br>


**www.murata-ps.com/support** 

**MDC_OKL2-T20-W12.B02** Page 12 of 19 

## **- - OKL2 T/20 W12 Series** 

Programmable Output 20-Amp **i** LGA SMT PoL DC-DC Converter Series 

**==> picture [488 x 311] intentionally omitted <==**

**----- Start of picture text -----**<br>
RECOMMENDED LAYOUT<br>TOP VIEW<br>Unit:mm<br>1.22 7.54 4.83 4.83 4.82 4.83 4.95<br>8 PLACES<br>7 6 5 4 3<br>(B) (B) (B) (B) (B)<br>1 . oo Pepe —<br>(B)<br>10<br>(A)<br>8<br>(B) 2<br>(B) 9 (A)<br>| | P o t<br>a 1 d Te<br>2 PLACES 1.90<br>Product  outline<br>1.52<br>5.46<br>5.21<br>13.46<br>6.09<br>5.46<br>**----- End of picture text -----**<br>


## SOLDER PAD NOTES: 

[1] To avoid incorrect contacts with exposed vias and plated through holes on the bottom of the converter, do not have any exposed copper in the center area of the host PC board (see drawing). Except for connections to the pads, keep all external circuits away from the board edges. 

[2] Do not connect any additional components between the Trim pin and Vout or between the Trim and Sense pins. Use only the specified connections. 

Dimensions are in inches (mm shown for ref. only). **Third Angle Projection** Tolerances (unless otherwise specified): .XX ± 0.02 (0.5) .XXX ± 0.010 (0.25) Angles ± 1˚ 

Components are shown for reference only. 

**www.murata-ps.com/support** 

**MDC_OKL2-T20-W12.B02** Page 13 of 19 

## **- - OKL2 T/20 W12 Series** 

## Programmable Output 20-Amp **i** LGA SMT PoL DC-DC Converter Series 

## **TAPE AND REEL INFORMATION (MSL RATING 2)** 

## **Tape Detail** 

**==> picture [328 x 162] intentionally omitted <==**

**----- Start of picture text -----**<br>
JP ef ys Pet Cy v |<br>cen<br>+f of of P-O FO - Cos fet a a ef af th a — of of a th 1<br>cso eax _| Z 8.95 +0.1<br>Vacuum Pickup<br>Point in Center Pulling direction<br>1 re |<br>1 | | j<br>A-A' SECTION<br>B-B' SECTION<br>**----- End of picture text -----**<br>


**==> picture [24 x 11] intentionally omitted <==**

**----- Start of picture text -----**<br>
Reel<br>**----- End of picture text -----**<br>


## **Reel Information (200 units per reel)** 

## **Reel Information (200 units per reel)** 

|**Key**|**Description**|**Length(mm)**|
|---|---|---|
|A|Tape trailer (no modules)|240±40|
|B|Pocket tape length before modules|240±60|
|C|Cover tape length before pocket tape|240±40|



**www.murata-ps.com/support** 

**MDC_OKL2-T20-W12.B02** Page 14 of 19 

## **- - OKL2 T/20 W12 Series** 

## Programmable Output 20-Amp **i** LGA SMT PoL DC-DC Converter Series 

## **TECHNICAL NOTES** 

## **Output Voltage Adustment** 

The output voltage may be adjusted over a limited range by connecting an external trim resistor (Rtrim) between the Trim pin and Ground. The Rtrim resistor must be a 1/10 Watt precision metal fi lm type,±0.5% accuracy or better with low temperature coeffi cient, ±100 ppm/degC. or better. Mount the resistor close to the converter with very short leads or use a surface mount trim resistor. 

In the table below, the calculated resistance is given. Do not exceed the specifi ed limits of the output voltage or the converter’s maximum power rating when applying these resistors. Also, avoid high noise at the Trim input. However, to prevent instability, you should never connect any capacitors to Trim. 

capacitor inputs), the converter shuts off and then restarts as the external capacitor recharges. Such situations could oscillate. To prevent this, make sure the operating input voltage is well above the UV Shutdown voltage AT ALL TIMES. 

## **Start-Up Time** 

Assuming that the output current is set at the rated maximum, the Vin to Vout Start-Up Time (see Specifi cations) is the time interval between the point when the ramping input voltage crosses the Start-Up Threshold and the fully loaded regulated output voltage enters and remains within its specifi ed accuracy band. Actual measured times will vary with input source impedance, external input capacitance, input voltage slew rate and fi nal value of the input voltage as it appears at the converter. 

## **OKL2-T/20-W12** 

**==> picture [202 x 17] intentionally omitted <==**

**----- Start of picture text -----**<br>
Output Voltage Calculated Rtrim (KΩ)<br>**----- End of picture text -----**<br>


|**Output Voltage**|**Calculated Rtrim (KΩ)**|
|---|---|
|||
|5.0 V|1.60|
|3.3 V|2.64|
|2.5 V|3.81|
|2.0 V|5.27|
|1.8 V|6.22|
|1.5 V|8.52|
|1.2 V|13.53|
|1.0 V|22.26|
|0.69 V|∞ (open)|



## **Resistor Trim Equation, OKL2-T/20-W12 models:** 

6.9 RTRIM (kΩ) =[_________] VOUT – 0.69 

## **Input Fusing** 

Certain applications and/or safety agencies may require fuses at the inputs of power conversion components. Fuses should also be used when there is the possibility of sustained input voltage reversal which is not current limited. For greatest safety, we recommend a fast blow fuse installed in the ungrounded input supply line. 

The installer must observe all relevant safety standards and regulations. 

For safety agency approvals, install the converter in compliance with the end-user safety standard. 

## **Input Under-Voltage Shutdown and Start-Up Threshold** 

Under normal start-up conditions, converters will not begin to regulate properly until the ramping-up input voltage exceeds and remains at the Start-Up Threshold Voltage (see Specifi cations). Once operating, converters will not turn off until the input voltage drops below the Under-Voltage Shutdown Limit. Subsequent restart will not occur until the input voltage rises again above the Start-Up Threshold. This built-in hysteresis prevents any unstable on/off operation at a single input voltage. 

Users should be aware however of input sources near the Under-Voltage Shutdown whose voltage decays as input current is consumed (such as 

These converters include a soft start circuit to moderate the duty cycle of its PWM controller at power up, thereby limiting the input inrush current. The On/Off Remote Control interval from On command to Vout regulated 

assumes that the converter already has its input voltage stabilized above the Start-Up Threshold before the On command. The interval is measured from the On command until the output enters and remains within its specifi ed accuracy band. The specifi cation assumes that the output is fully loaded at maximum rated current. Similar conditions apply to the On to Vout regulated specifi cation such as external load capacitance and soft start circuitry. 

## **Recommended Input Filtering** 

The user must assure that the input source has low AC impedance to provide dynamic stability and that the input supply has little or no inductive content, including long distributed wiring to a remote power supply. The converter will operate with no additional external capacitance if these conditions are met. 

For best performance, we recommend installing a low-ESR capacitor immediately adjacent to the converter’s input terminals. The capacitor should be a ceramic type such as the Murata GRM32 series or a polymer type. Initial suggested capacitor values are 44 μF, rated at twice the expected maximum input voltage. Make sure that the input terminals do not go below the under voltage shutdown voltage at all times. More input bulk capacitance may be added in parallel (either electrolytic or tantalum) if needed. 

## **Recommended Output Filtering** 

The converter will achieve its rated output ripple and noise with no additional external capacitor. However, the user may install more external output capacitance to reduce the ripple even further or for improved dynamic response. Again, use low-ESR ceramic (Murata GRM32 series) or polymer capacitors. Initial values of 188 μF may be tried, either single or multiple capacitors in parallel. Mount these close to the converter. Measure the output ripple under your load conditions. 

Use only as much capacitance as required to achieve your ripple and noise objectives. Excessive capacitance can make step load recovery sluggish or possibly introduce instability. Do not exceed the maximum rated output capacitance listed in the specifi cations. 

**www.murata-ps.com/support** 

**MDC_OKL2-T20-W12.B02** Page 15 of 19 

## **- - OKL2 T/20 W12 Series** 

## Programmable Output 20-Amp **i** LGA SMT PoL DC-DC Converter Series 

## **Input Ripple Current and Output Noise** 

All models in this converter series are tested and specifi ed for input refl ected ripple current and output noise using designated external input/ output components, circuits and layout as shown in the fi gures below. The Cbus and Lbus components simulate a typical DC voltage bus. Please note that the values of Cin, Lbus and Cbus will vary according to the specifi c converter model. 

**==> picture [250 x 120] intentionally omitted <==**

**----- Start of picture text -----**<br>
TO<br>OSCILLOSCOPE CURRENT<br>PROBE<br>+VIN<br>LBUS<br>+<br>VIN – CBUS CIN<br>+<br>–<br>-VIN<br>CIN = 2 x 100μF, ESR < 700mΩ @ 100kHzIN = 2 x 100μF, ESR < 700mΩ @ 100kHz = 2 x 100μF, ESR < 700mΩ @ 100kHz<br>**----- End of picture text -----**<br>


CIN = 2 x 100μF, ESR < 700mΩ @ 100kHzIN = 2 x 100μF, ESR < 700mΩ @ 100kHz = 2 x 100μF, ESR < 700mΩ @ 100kHz CBUS = 1000μF, ESR < 100mΩ @ 100kHz 

LBUS = 1μH 

Figure 4. Measuring Input Ripple Current 

**==> picture [248 x 122] intentionally omitted <==**

**----- Start of picture text -----**<br>
+VOUT<br>Cext SCOPE RLOAD<br>-VOUT<br>**----- End of picture text -----**<br>


Figure 5. Measuring Output Ripple and Noise (PARD) The capacitor Cext value is found on the electrical data page. 

## **Minimum Output Loading Requirements** 

All models regulate within specifi cation and are stable under no load to full load conditions. Operation under no load might, however, slightly increase output ripple and noise. 

## **Thermal Shutdown** 

To prevent many over temperature problems and damage, these converters include thermal shutdown circuitry. If environmental conditions cause the temperature of the DC-DCs to rise above the Operating Temperature Range up to the shutdown temperature, an on-board electronic temperature sensor will power down the unit. When the temperature decreases below the turn-on threshold, the converter will automatically restart. 

## **Temperature Derating Curves** 

The graphs in this data sheet illustrate typical operation under a variety of conditions. The derating curves show the maximum continuous ambient air temperature and decreasing maximum output current which is acceptable under increasing forced airfl ow measured in Linear Feet per Minute (“LFM”). Note that these are AVERAGE measurements. The converter will accept brief increases in current or reduced airfl ow as long as the average is not exceeded. 

Note that the temperatures are of the ambient airfl ow, not the converter itself which is obviously running at higher temperature than the outside air. Also note that very low fl ow rates (below about 25 LFM) are similar to “natural convection,” that is, not using fan-forced airfl ow. Murata makes Characterization measurements in a closed cycle wind tunnel with calibrated airfl ow. We use both thermocouples and an infrared camera system to observe thermal performance. 

CAUTION: These graphs are all collected at slightly above Sea Level altitude. Be sure to reduce the derating for higher density altitude. 

## **Output Voltage Sequencing** 

The OKL modules include a sequencing feature that enables users to implement various types of output voltage sequencing in their applications. This is accomplished via an additional sequencing pin. When not using the sequencing feature, either tie the sequence pin to Vin or leave it unconnected. 

When an analog voltage is applied to the sequence pin, the output voltage tracks this voltage until the output reaches the set-point voltage. The fi nal value of the sequence voltage must be set higher than the setpoint voltage of the module. The output voltage follows the voltage on the sequence pin on a one-to-one volt basis. By connecting multiple modules together, multiple modules can track their output voltages to the voltage applied on the sequence pin. 

For proper voltage sequencing, fi rst, input voltage is applied to the module. The On/Off pin of the module is left unconnected (or tied to GND for negative logic modules or tied to Vin for positive logic modules) so that the module is ON by default. After applying input voltage to the module, a minimum 10msec delay is required before applying voltage on the sequence pin. During this time, a voltage of 50mV (± 20 mV) is maintained on the sequence pin. This delay gives the module enough time to complete its internal powerup soft-start cycle. During the delay time, the sequence pin should be held close to ground (nominally 50mV ± 20 mV). This is required to keep the internal opamp out of saturation thus preventing output overshoot during the start of the sequencing ramp. By selecting resistor R1 according to the following equation 

**==> picture [78 x 19] intentionally omitted <==**

the voltage at the sequencing pin will be 50mV when the sequencing signal is at zero. See fi gure 6 for R1 connection for the sequencing signal to the SEQ pin. 

CAUTION: If you operate too close to the thermal limits, the converter may shut down suddenly without warning. Be sure to thoroughly test your application to avoid unplanned thermal shutdown. 

**www.murata-ps.com/support** 

**MDC_OKL2-T20-W12.B02** Page 16 of 19 

## **- - OKL2 T/20 W12 Series** 

## Programmable Output 20-Amp **i** LGA SMT PoL DC-DC Converter Series 

## **Output Current Limiting** 

Current limiting inception is defi ned as the point at which full power falls below the rated tolerance. See the Performance/Functional Specifi cations. Note particularly that the output current may briefl y rise above its rated value in normal operation as long as the average output power is not exceeded. This enhances reliability and continued operation of your application. If the output current is too high, the converter will enter the short circuit condition. 

## **Output Short Circuit Condition** 

When a converter is in current-limit mode, the output voltage will drop as the output current demand increases. If the output voltage drops too low (approximately 98% of nominal output voltage for most models), the magnetically coupled voltage used to develop primary side voltages will also drop, thereby shutting down the PWM controller. Following a time-out period, the PWM will restart, causing the output voltage to begin ramping up to its appropriate value. If the short-circuit condition persists, another shutdown cycle will initiate. This rapid on/off cycling is called “hiccup mode”. The hiccup cycling reduces the average output current, thereby preventing excessive internal temperatures and/or component damage. A short circuit can be tolerated indefi nitely. 

**==> picture [246 x 178] intentionally omitted <==**

**----- Start of picture text -----**<br>
OKL P Module<br>+Vin +Vin<br>E<br>Rp<br>On/Off R1<br>PWM<br>Q1<br>GND GND<br>BOM � Rp � 20K<br>BOM � Q1 � Q SMT MOS P 30V<br>**----- End of picture text -----**<br>


Figure 6. On/Off Circuit Control for Using Positive On/Off Logic 

**==> picture [246 x 165] intentionally omitted <==**

**----- Start of picture text -----**<br>
OKL N Module<br>+Vin +Vin<br>E PWM<br>Rp<br>On/Off<br>Q3<br>GND<br>Q1<br>GND GND<br>BOM    Rp    20K<br>BOM    Q1    Q SMT MOS P 30V<br>**----- End of picture text -----**<br>


The “hiccup” system differs from older latching short circuit systems because you do not have to power down the converter to make it restart. The system will automatically restore operation as soon as the short circuit condition is removed. 

## **Remote On/Off Control** 

The OKL Series power modules can be specifi ed with either a positive or negative logic type. See Figures 6 and 7 for On/Off circuit control. In the positive logic on/off option the unit turns on during a logic high on the On/Off pin and turns off during a logic low. In a negative logic on/off option, the unit turns off during logic high and on during logic low. The On/Off signal should always be reference to ground. For positive or negative option, leaving then On/Off pin disconnected will turn the unit on when input voltage is present. 

Positive—Units are enabled when the on/off pin is left open or is pulled high to +Vin. The On/Off circuit control is shown in fi gure 6. When the external transistor Q1 is in the off state, the internal PWM enable pin is pull high causing the unit to turn on. When Q1 is turn on, the On/Off pin is pulled low and the units is off. Rp should be around 20K ohms. 

Negative—Units are enabled when the ON/Off is open or brought to within a low voltage (see specifi cations) with respect to –Vin. The unit is off when the ON/Off is pulled high with respect to –Vin (see specifi cations). The On/Off circuitry is shown in fi gure 7. The On/Off pin should be pulled high with an external pull-up resistor (20K ohms). When Q1 is in the off state, the On/Off pin is pulled high, transistor Q3 is turn on and the unit is off. To turn on the unit, Q1 is turn on, pulling the On/Off pin low and turning Q3 off resulting on the unit being on. 

Dynamic control of the On/Off function should be able to sink the specifi ed signal current when brought low and withstand appropriate voltage when brought high. Be aware too that there is a fi nite time in milliseconds (see specifi cations) between the time of On/Off Control activation and stable, regulated output. This time will vary slightly with output load type and current and input conditions. 

## **Output Capacitive Load** 

These converters do not require external capacitance added to achieve rated specifi cations. Users should only consider adding capacitance to reduce switching noise and/or to handle spike current load steps. Install only enough capacitance to achieve noise objectives. Excess external capacitance may cause regulation problems, degraded transient response and possible oscillation or instability. 

## **Synchronization** 

These converters can be synchronized using an external signal. 

Details of the SYNC signal are provided in the Performance and Functional Specifi cations table. 

If the synchronization function is not being used, leave the SYNC pin fl oating. 

When synchronization function is used, output ripple may increase on some operating conditions. Please check the proper operation of this device with the peripheral circuits on your system. 

Figure 7. On/Off Circuit Control for Using Negative On/Off Logic 

**www.murata-ps.com/support** 

**MDC_OKL2-T20-W12.B02** Page 17 of 19 

## **- - OKL2 T/20 W12 Series** 

Programmable Output 20-Amp **i** LGA SMT PoL DC-DC Converter Series 

## **Voltage Range Graph** 

Please observe the limits below for voltage input and output ranges. These limits apply at all output currents (Ta = 25°C). 

**==> picture [532 x 398] intentionally omitted <==**

**----- Start of picture text -----**<br>
16 15<br>14 1413 nn<br>12<br>oe ee Vin=14V / Vout=1V ee ee 12 | | | | Jee<br>10 re Ae a<br>ee 11 Aaa<br>8 ee<br>10<br>Vin=4.5V / Vout=3.3V<br>6 TOTO AES without Sync (400kHz)<br>9<br>> | f | A) dl<br>4 Sync 420kHz<br>8<br>Upper Limit Sync 520kHz<br>2 7<br>Lower Limit Sync 600kHz<br>0 eeTe 6 <7<br>0 1 2 3 4 5 6 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3 1.4 1.5<br>Output Voltage (V) Output Voltage (V)<br>Figure 8. Voltage Range Graph Figure 9 Voltage Range Graph (range expansion)<br>Soldering Guidelines Recommended Lead-free Solder Refl ow Profi le<br>Murata Power Solutions recommends the specifi cations below when installing these converters. These specifi cations vary depending on the solder type. Exceeding these converters. These specifi cations vary depending on the solder type. Exceeding these  250 Peak Temp.  235-260° C<br>specifi cations may cause damage to the product. Your production environment may differ<br>therefore please thoroughly review these guidelines with your process engineers. 200<br>Reflow Solder Operations for surface-mount products (SMT) 150 Reflow Zone<br>For Sn/Ag/Cu based solders: Soaking Zone time above 217° C<br>Preheat Temperature Less than 1 ºC. per second 100 120 sec max 45-75 sec<br>Time over Liquidus 45 to 75 seconds <1.5° C/sec High trace = normal upper limit<br>Preheating Zone Low trace = normal lower limit<br>Maximum Peak Temperature 260 ºC. 50<br>240 sec max<br>Cooling Rate Less than 3 ºC. per second<br>For Sn/Pb based solders: 0 0 30 60 90 120 150 180 210 240 270 300<br>Time (sec)<br>Input Voltage (V) Input Voltage (V)<br>Temperature (°C)<br>**----- End of picture text -----**<br>


## **Soldering Guidelines** 

Murata Power Solutions recommends the specifi cations below when installing these converters. These specifi cations vary depending on the solder type. Exceeding these converters. These specifi cations vary depending on the solder type. Exceeding these specifi cations may cause damage to the product. Your production environment may differ therefore please thoroughly review these guidelines with your process engineers. 

|~~**Reflow Solder Operations for surface-mount products (SMT)**~~|~~**Reflow Solder Operations for surface-mount products (SMT)**~~|
|---|---|
|**For Sn/Ag/Cu based solders:**||
|Preheat Temperature|Less than 1 ºC. per second|
|Time over Liquidus|45 to 75 seconds|
|Maximum Peak Temperature|260 ºC.|
|Cooling Rate|Less than 3 ºC. per second|
|**For Sn/Pb based solders:**||
|Preheat Temperature|Less than 1 ºC. per second|
|Time over Liquidus|60 to 75 seconds|
|Maximum Peak Temperature|235 ºC.|
|Cooling Rate|Less than 3 ºC. per second|



**==> picture [241 x 64] intentionally omitted <==**

**----- Start of picture text -----**<br>
CAUTION: Do not refl ow the DC-DC converter as follows, because the<br>DC-DC converter may fall from the substrate during refl owing.<br>/ Te DC-DC Converter<br>Substrate<br>**----- End of picture text -----**<br>


**www.murata-ps.com/support** 

**MDC_OKL2-T20-W12.B02** Page 18 of 19 

## **- - OKL2 T/20 W12 Series** 

Programmable Output 20-Amp **i** LGA SMT PoL DC-DC Converter Series 

## **Vertical Wind Tunnel** 

**==> picture [285 x 281] intentionally omitted <==**

**----- Start of picture text -----**<br>
IR Transparent<br>optical window Variable<br>Unit under speed fan<br>test (UUT)<br>IR Video<br>Camera<br>ms)<br>Heating<br>element<br>Precision<br>low-rate<br>>See<br>anemometer<br>3” below UUT<br>Ambient<br>temperature<br>sensor<br>—<br>Airflow<br>collimator<br>y)<br>**----- End of picture text -----**<br>


Murata Power Solutions employs a computer controlled custom-designed closed loop vertical wind tunnel, infrared video camera system, and test instrumentation for accurate airfl ow and heat dissipation analysis of power products. The system includes a precision low fl ow-rate anemometer, variable speed fan, power supply input and load controls, temperature gauges, and adjustable heating element. 

The IR camera monitors the thermal performance of the Unit Under Test (UUT) under static steady-state conditions. A special optical port is used which is transparent to infrared wavelengths. 

Both through-hole and surface mount converters are soldered down to a 10" x 10" host carrier board for realistic heat absorption and spreading. Both longitudinal and transverse airfl ow studies are possible by rotation of this carrier board since there are often signifi cant differences in the heat dissipation in the two airfl ow directions. The combination of adjustable airfl ow, adjustable ambient heat, and adjustable Input/Output currents and voltages mean that a very wide range of measurement conditions can be studied. 

The collimator reduces the amount of turbulence adjacent to the UUT by minimizing airfl ow turbulence. Such turbulence infl uences the effective heat transfer characteristics and gives false readings. Excess turbulence removes more heat from some surfaces and less heat from others, possibly causing uneven overheating. 

Both sides of the UUT are studied since there are different thermal gradients on each side. The adjustable heating element 

and fan, built-in temperature gauges, and no-contact IR camera mean that power supplies are tested in real-world conditions. 

Figure 10. Vertical Wind Tunnel 

Murata Power Solutions, Inc. 11 Cabot Boulevard, Mansfi eld, MA 02048-1151 U.S.A. ISO 9001 and 14001 REGISTERED 

**This product is subject to the following operating requirements and the Life and Safety Critical Application Sales Policy:** A **Refer to:** ~~a~~ **http://www.murata-ps.com/requirements/** Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifi cations are subject to change without notice. _**© 2016 Murata Power Solutions, Inc.**_ 

**www.murata-ps.com/support** 

**MDC_OKL2-T20-W12.B02** Page 19 of 19