LA 100-P/SP13

## **Current Transducer LA 100-P/SP13** 

## _I_ **= 100 A** PN 

For the electronic measurement of currents: DC, AC, pulsed..., with galvanic separation between the primary circuit and the secondary circuit. 

## ~~**Electrical data**~~ 

|_I_PN<br>_I_PM|Primary nominal rms current<br>Primary current, measuring range|100<br>0 .. ±160|A<br>A|
|---|---|---|---|
|_R_M|Measuring resistance @ 70 °C|||
|||_R_M min _R_M max||
||with ±12 V<br>@ ±100 Amax|10<br>65|Ω|
||@ ±160 Amax|10<br>30|Ω|
||with ±15 V<br>@ ±100 Amax|40<br>95|Ω|
|_I_SN|@ ±160 Amax<br>Secondary nominal rms current|40<br>50<br>100|Ω<br>mA|
|_K_N<br>_U_C<br>_I_C|Conversion ratio<br>Supply voltage (±5 %)<br>Current consumption|1 : 1000<br>±12 .. 15<br>10(@ ±15 V) +_I_S|V<br>mA|
|**Accuracy - Dynamic performance data**||||
|_X_<br>_ε_L<br>_I_O<br>_I_OM<br>_I_O_T_<br>_t_ra|Accuracy @_I_PN,_T_A= 25 °C<br>@ ±15 V (±5 %)<br>@ ±12 .. 15 V (±5 %)<br>Linearity error<br>Offset current @_I_P= 0,_T_A= 25 °C<br>Magnetic offset current1)@_I_P= 0 and specified_R_M,<br>after an overload of 3 ×_I_PN<br>Temperature variation of_I_O<br>-25 °C .. +70 °C<br>Reaction time|±0.45<br>±0.70<br>< 0.15<br>Typ<br>Max<br>±0.2<br>±0.3<br>±0.1<br>±0.5<br><500|%<br>%<br>%<br>mA<br>mA<br>mA<br>ns|
|_t_r|Step response time2)to 90 % of_I_PN|<1|µs|
|d_i/_d_t_|d_i_/d_t_accurately followed|>200|A/µs|
|_BW_|Frequency bandwidth (-1 dB)|DC .. 200|kHz|
|~~**General data**~~||||
|_T_A<br>_T_S<br>_R_S<br>_m_|Ambient operating temperature<br>Ambient storage temperature<br>Resistance of secondary winding @_T_A= 70 °C<br>Mass<br>Standards|-25 .. +70<br>°C<br>-40 .. +90<br>°C<br>25<br>Ω<br>18<br>g<br>EN 50178: 1997<br>UL 508: 2010||



Notes:[1)] Result of the coercive field of the magnetic circuit 

- 2)  With a d _i_ /d _t_ of 100A/ µs. 

## **Features** 

- ●Closed loop (compensated) current transducer using the Hall effect 

- ●Insulating plastic case recognized according to UL 94-V0. 

## **Special features** 

- _I_ PM = 0 .. ±160 A 

- _K_ N = 1 : 1000 

- _T_ A = -25 °C .. +70 °C. 

## **Advantages** 

- ●Excellent accuracy 

- ●Very good linearity 

- ●Low temperature drift 

- ●Optimized response time 

- ●Wide frequency bandwidth 

- ●No insertion losses 

- ●High immunity to external interference 

- ●Current overload capability. 

## **Applications** 

- ●AC variable speed drives and servo motor drives 

- ●Static converters for DC motor drives 

- ●Battery supplied applications 

- ●Uninterruptible Power Supplies (UPS) 

- ●Switched Mode Power Supplies (SMPS) 

- ●Power supplies for welding applications. 

## **Application domain** 

- ●Industrial. 

N° 97.09.34.013.0 

Page 1/3 

3February2015/version 5 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice 

www.lem.com 

## **Current Transducer LA 100-P/SP13** 

|~~**Insulation coordination**~~|~~**Insulation coordination**~~|||
|---|---|---|---|
|_U_d|Rms voltage for AC insulation test, 50 Hz/1 min|2.5|kV|
|_Û_W|Impulse withstand voltage 1.2/50 µs|4.5|kV|
|||Min||
|_d_Cp|Creepage distance1)|3.8|mm|
|_d_CI|Clearance2)|3.8|mm|
|_CTI_|Comparative tracking index (group I)|600||



Notes:[1)] Distance between hole busbar and winding 

2)  Direct distance between hole busbar and winding. 

## **Applications examples** 

**According to EN 50178 and IEC 61010-1 standards** and following conditions: 

- ●Over voltage category OV 3 

- ●Pollution degree PD2 

- ●Non-uniform field 

||**EN 50178**|**IEC 61010-1**|
|---|---|---|
|_d_Cp,_d_CI,_Û_W|Rated insulation voltage|Nominal voltage|
|Basic insulation|300 V|300 V|
|Reinforced insulation|150 V|150 V|



## **Safety** 

This transducer must be used in limited-energy secondary circuits according to IEC 61010-1. 

This transducer must be used in electric/electronic equipment with respect to applicable standards and safety requirements in accordance with the manufacturer’s operating instructions. 

Caution, risk of electrical shock 

When operating the transducer, certain parts of the module can carry hazardous voltage (eg. primary busbar, power supply). 

Ignoring this warning can lead to injury and/or cause serious damage. This transducer is a build-in device, whose conducting parts must be inaccessible after installation. 

A protective housing or additional shield could be used. 

Main supply must be able to be disconnected. 

Page 2/3 

3February2015/version 5 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice 

www.lem.com 

## **Dimensions LA 100-P/SP13** (in mm) 

**==> picture [511 x 372] intentionally omitted <==**

**----- Start of picture text -----**<br>
Connection<br>I P<br>I S R M<br>U C<br>U C d Cl d Cp<br>**----- End of picture text -----**<br>


## **Mechanical characteristics** 

- ●General tolerance 

- ●General tolerance ±0.2 mm ●Primary through-hole 12.7 × 7 mm ●Fastening & connection of secondary 3 pins 0.6 × 0.7 mm 

- ●Recommended PCB hole 1.2 mm 

## **Remarks** 

- _I_ S is positive when _I_ P flows in the direction of the arrow. 

- ●Temperature of the primary conductor should not exceed 100 °C. 

- ●Installation of the transducer must be done unless otherwise specified on the datasheet, according to LEM Transducer Generic Mounting Rules. Please refer to LEM document N°ANE120504 available on our Web site: **Products/Product Documentation** . 

- ●Dynamic performances (d _i_ /d _t_ and response time) are best 

   - with a single bar completely filling the primary hole. 

- ●In order to achieve the best magnetic coupling, the primary windings have to be wound over the top edge of the device. 

Page 3/3 

LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice 

3February2015/version 5 

www.lem.com