HFE10-1/12-HT-L1

## **Features** 

- 50A switching capacity 

- Lamp load up to 5000W 

- Motor load up to 3HP 

- Max.inrush current 480A/2.1ms 

- Dielectric strength:more than 4kV 

- (between coil and contacts) 

- Manual switch function available 

- (A81) **:** Switching without load 

- (W): Contact gap available≥1.5mm 

## **CONTACT DATA** 

Single coil latching: Approx. 1.5W Double coils latching: Approx. 3.0W Type W-Single coil latching:Approx. 2.4W Type W-Double coils latching:Approx. 4.8W 

Contact arrangement 1A,1B,1C Contact resistance 1) Typical value:[2)] ≤20mΩ(1A 24VDC) Contact material AgSnO2 **(A81): Switching without load:** Making at 50A 250VAC, breaking (without load) 2x10[5] ops **Standard products:** 1A , 1B **:** 50A 277VAC , 1x10[5] ops(Resistive) Contact rating 5000W 240VAC , 3x10[4] ops trength (incandescent lamp) 16A 277VAC , 6000ops(Electronic ballast) 3HP 277VAC , 3x10[4] ops(Motor) 1Z **:** 40A 277VAC , 3x10[4] ops(Resistive) Max. switching voltage 440VAC Set Max. switching current 50A Reset Max. switching power 1A:12500VA /1C:10000VA M Mechanical endurance 1 X 10[6] ops ax. St Electrical endurance See “contact rating” ~~h~~ 

Rated power 

|(between input and output side)|(between input and output side)|(between input and output side)|(between input and output side)|(between input and output side)|
|---|---|---|---|---|



**Notes:** 1) The data shown above are initial values. 

- 2) Typical value: Sampling quantity for contact resistance shall not less than 20 pcs, take the average value from 5 continous measurements for each sample. 

|Nominal<br>Voltage<br>VDC|Set / Reset Voltage|Set / Reset Voltage|Set / Reset Voltage<br>VDC<br>1)|Pulse<br>Duration<br>ms min.|Coil Resistance<br>x (1±10%) Ω|Coil Resistance<br>x (1±10%) Ω|
|---|---|---|---|---|---|---|
|6|||≤4.8|≥50||24|
|9<br>12|||≤7.2<br>≤9.6|≥50<br>≥50|Single coil<br>latching|54<br>96|
|24|||≤19.2|≥50||384|
|48|||≤38.4|≥50||1536|
|6|||≤4.8|≥50||12+12|
|9|||≤7.2|≥50||27+27|
|12<br>24<br>48|||≤9.6<br>≤19.2<br>≤38.4|≥50<br>≥50<br>≥50|Double coils<br>latching|48+48<br>192+192<br>768+768<br>Double coils|



|-40|-40|oC ~ 85<br>oC|oC ~ 85<br>oC|
|---|---|---|---|
||||PCB|
|||||
|||||
|||POB&AC||
||Approx|Approx~~.~~|26<br>9g|



Notes:1) The data shown above are initial values. 2) The above set voltage, reset voltage are the test value for relay without load. Please use 1~1.5 times of rated voltage to drive the relay for your application. 

HONGFA RELAY ISO9001 IATF16949 ISO14001 ISO45001 

IECQ QC 080000 ISO/EC 27001 2025 Rev.1.00 are required, please contact us. 

82 

## **COIL DATA** 

Type W-Single coil latching 

Type W-Double coils latching 

**==> picture [456 x 488] intentionally omitted <==**

**----- Start of picture text -----**<br>
Nominal Pulse  Nominal Pulse<br>Voltage Set / Reset Voltage Duration Coil Resistance  Voltage Set / Reset Voltage Duration Coil Resistance<br>VDC VDC max. 1) ms min. x (1±10%) Ω VDC VDC max. 1) ms min. x (1±10%) Ω<br>≥50 15 ≥50 7.5+7.5<br>≥50 33.8 ≥50 16.9+16.9<br>≥50 60 ≥50 30+30<br>≥50 240 ≥50 120+120<br>≥50 960 ≥50 480+480<br>Notes:1) The data shown above are initial values.<br>          2)The above set voltage, reset voltage are the test value for relay without load. Please use 1~1.5 times of rated voltage to drive the relay for<br>              your application.<br>          3) W-type for special  code (W).<br>Contact<br>（ Not applicable to HFE10-5 ）<br>arrangement<br>Extended terminal<br>Extended bending terminal<br>Coil type<br>R:  Reverse polarity                   Nil:  Standard polarity<br>(W):  Relay with approx. 1.5mm contact gap<br>         (Only for 1 form A, with VDE certification(250VAC 32A))<br>XXX:  Customer special requirement (A81): switching without load<br>**----- End of picture text -----**<br>


The termination type 1, type 5, type 6, type7 are 

83 

## **Outline Dimensions** 

**==> picture [435 x 195] intentionally omitted <==**

**----- Start of picture text -----**<br>
7.5±0.1<br>5.2  [+0.4]<br>15±0.25 -0.2<br>Not applicable to<br>normally open type 1.5 +0.3 -0.1<br>2.4±0.05<br>0.64 +0.2 -0.1 Double coil type only<br>30.2±0.3 10±0.1<br> +0.3  -0.1<br> +0.2  -0.1<br>**----- End of picture text -----**<br>


**==> picture [428 x 195] intentionally omitted <==**

**----- Start of picture text -----**<br>
7.5±0.25<br>15±0.25 5.2 [+0.4] -0.2<br>1.5 +0.3 -0.1<br>0.64 +0.2 -0.1<br>Double coil type only<br>29.3±0.3 10±0.1<br> +0.3  -0.1<br> +0.2  -0.1<br>**----- End of picture text -----**<br>


84 

## **Outline Dimensions** 

**==> picture [447 x 283] intentionally omitted <==**

**----- Start of picture text -----**<br>
7.5±0.1<br>15±0.25<br>28.6±0.3<br>5.2 +0.4-0.2<br>30.2±0.3 0.64 +0.2 -0.1 Double coil type only<br>10±0.1<br>54.2±0.3<br> +0.3  -0.1<br> +0.2  -0.1<br> +0.3  -0.1  +0.3  -0.1<br>**----- End of picture text -----**<br>


**==> picture [427 x 191] intentionally omitted <==**

**----- Start of picture text -----**<br>
9.2±0.1<br>15±0.25 7.6±0.3<br>5.2 +0.4-0.2<br>0.64 +0.2 -0.1 Double coil type only<br>30.2±0.3 10±0.1<br> +0.3  -0.1<br> +0.2  -0.1<br>**----- End of picture text -----**<br>


85 

## **Outline Dimensions** 

**==> picture [457 x 285] intentionally omitted <==**

**----- Start of picture text -----**<br>
32.8±0.3<br>12±0.4<br> +0.3<br> -0.1  +0.3<br> -0.1<br>5.2 +0.4-0.2<br>15±0.25 30.2±0.3 0.64 +0.2 -0.1 Double coil type only<br>10±0.1<br> +0.2  -0.1<br>**----- End of picture text -----**<br>


**==> picture [419 x 200] intentionally omitted <==**

**----- Start of picture text -----**<br>
7.5±0.1<br>15±0.25 5.2 +0.4-0.2<br> +0.3<br>1.7 -0.1<br>0.64 +0.2 -0.1 Double coil type only<br>30.2±0.3 10±0.1<br> +0.3  -0.1<br> +0.2  -0.1<br>**----- End of picture text -----**<br>


86 

## **Wiring Diagram** 

Standard polarity 

**==> picture [454 x 41] intentionally omitted <==**

**==> picture [198 x 33] intentionally omitted <==**

**==> picture [198 x 35] intentionally omitted <==**

**==> picture [222 x 68] intentionally omitted <==**

**==> picture [198 x 32] intentionally omitted <==**

Reverse polarity 

**==> picture [449 x 47] intentionally omitted <==**

**==> picture [198 x 31] intentionally omitted <==**

**==> picture [196 x 34] intentionally omitted <==**

**==> picture [220 x 60] intentionally omitted <==**

**==> picture [198 x 36] intentionally omitted <==**

87 

## **Wiring Diagram** 

## Standard polarity 

**==> picture [452 x 40] intentionally omitted <==**

**==> picture [198 x 31] intentionally omitted <==**

**==> picture [197 x 34] intentionally omitted <==**

Reverse polarity 

**==> picture [451 x 35] intentionally omitted <==**

**==> picture [212 x 196] intentionally omitted <==**

**==> picture [198 x 32] intentionally omitted <==**

88 

## **CAUTIONS** 

- 1.The recommended soldering temperature range is 250±10°C with the duration of 2 5s. It is not suggested to apply reflow soldering method, if it is required indeed, please contact with our technicians. It is general required that the wave soldering temperature at 250°C shall not more than 2s. 

2. Latching relay is on the "reset" or "set" status when delivery, with the consideration of shock risen from transit and relay mounting, relay would be changed to "set" or "reset" status, therefore, when application ( connecting the power supply), please reset the 

relay to "set" or "reset" status on request. 

3. In order to maintain "set" or "reset" status, energized voltage applied across the coil should reach the rated voltage, impulse width should be 5 times more than "set" or "reset" time. Do not energize voltage to "set" coil and "reset" coil simultaneously. And also long energized time (more than 1 min) should be avoided. 

**==> picture [327 x 141] intentionally omitted <==**

**==> picture [37 x 41] intentionally omitted <==**

**==> picture [454 x 59] intentionally omitted <==**

89