B-TL70-Q1PMA

TL70 Modular Tower Light Quick Start Guide 

## Overview 

This guide is designed to help you set up and install the TL70 Modular Tower Light. For complete information on programming, performance, troubleshooting, dimensions, and accessories, please refer to the Product Manual at www.bannerengineering.com. Search for part number 182214 to view the Product Manual. Use of this document assumes familiarity with pertinent industry standards and practices. 

## Configuring the Modules 

**==> picture [427 x 259] intentionally omitted <==**

**----- Start of picture text -----**<br>
DIP Switches<br>Assembly Options<br>7 8 9 10 1 2 3 4 5 6 7 8<br>Module 1 ON<br>Module 2 ON<br>Light and<br>Module 3 ON<br>Standard<br>Module 6 Audible  Module 4 ON<br>Components<br>Module 5 ON<br>Module 5 Module 6 ON<br>3 Hz ON OF<br>Module 4 Light and<br>Module Flash  1.5 Hz ON ON<br>Rate<br>Module 3 Solid On* OFF OFF<br>Pulse 1.5<br>ON OFF<br>Module 2 Hz<br>Standard<br>Audible  Chirp Alarm ON ON<br>Module<br>Module 1 Siren Alarm OFF ON<br>Settings<br>Continuous<br>OFF OFF<br>Base Alarm*<br>**----- End of picture text -----**<br>


**==> picture [205 x 29] intentionally omitted <==**

**----- Start of picture text -----**<br>
1 2 3 4 5 6 7 8 9 10<br>Turn on the appropriate DIP switch to set the order of the<br>components, counting up from the tower light's base.<br>**----- End of picture text -----**<br>


**==> picture [500 x 143] intentionally omitted <==**

**----- Start of picture text -----**<br>
DIP Switches<br>Assembly Options<br>1 2 3 4 5 6 7 8 9 10<br>Pulse 1.5 Hz ON OFF<br>Chirp Alarm ON ON<br>Siren Alarm OFF ON<br>Continuous Alarm* OFF OFF<br>Loud Audible Module<br>Settings Low Intensity* OFF OFF<br>Med. Intensity ON OFF<br>Med./Loud Intensity OFF ON<br>Loud Intensity ON ON<br>**----- End of picture text -----**<br>


* Factory default setting 

Original Instructions 19-Aug-25 

© Banner Engineering Corp. All rights reserved. 

www.bannerengineering.com 

p/n: 182215 Rev. H 

TL70 Modular Tower Light Quick Start Guide 

## Assembling the Modules 

**==> picture [135 x 185] intentionally omitted <==**

**==> picture [134 x 167] intentionally omitted <==**

## To assemble the modules: 

1. Align the notches on each module and press together. 

2. Rotate the top module clockwise to lock into place (notches shown in the locked position). 

NOTE: DIP switches should remain in the default off position. 

## Wiring Diagrams 

**==> picture [500 x 328] intentionally omitted <==**

**----- Start of picture text -----**<br>
PNP Input NPN Input M12 Male Pinouts Key<br>Module bu (3) Module bu (3) 1 1 = brown2 = white<br>bk (4) 12–30 V DC bk (4) 12–30 V DC 2 3 = blue4 = black<br>M1 M1 4 5 = gray<br>M2 bn (1) M2 bn (1) 3 5 M1 = Module 1M2 = Module 2<br>M3 = Module 3<br>wh (2) M4 = Module 4<br>M3 wh (2)<br>M3<br>gy (5)<br>M4 gy (5)<br>M4<br>PNP Input NPN Input M12 Male Pinouts Key<br>Module bu (7) Module bu (7) 1 7 1 = white2 = brown<br>12–30 V DC 12–30 V DC 3 = green<br>M1 pk (6) M1 pk (6) 2 6 4 = yellow5 = gray<br>M2 bn (2) M2 bn (2) 34 5 6 = pink7 = blue8 = red<br>M3 wh (1) M3 wh (1) 8 M1 = Module 1M2 = Module 2<br>M3 = Module 3<br>M4 gy (5) M4 gy (5) M4 = Module 4M5 = Module 5<br>M6 = Module 6<br>M5 ye (4) M5 ye (4)<br>M6 rd (8) M6 rd (8)<br>gn (3) gn (3)<br>Not Used Not Used<br>**----- End of picture text -----**<br>


page 2 of 4 

© Banner Engineering Corp. All rights reserved. www.bannerengineering.com 

19-Aug-25 

TL70 Modular Tower Light Quick Start Guide 

NOTE: Models SG-TL70-ALM and SG-TL70-ALMC are not compatible with NPN input wiring. 

**==> picture [500 x 122] intentionally omitted <==**

**----- Start of picture text -----**<br>
Wiring Terminal Block Terminal Block Key<br>0 = DC common<br>1 = Module 1<br>2 = Module 2<br>3 = Module 3<br>4 = Module 4<br>5 = Module 5<br>6 = Module 6<br>**----- End of picture text -----**<br>


## Specifications 

Supply Voltage and Current 12 V DC to 30 V DC 

**==> picture [221 x 162] intentionally omitted <==**

**----- Start of picture text -----**<br>
Maximum Current (mA)<br>Indicator Color or Audible Model<br>at 24 V  at 30 V<br>at 12 V DC<br>DC DC<br>Blue, Green, White 420 200 150<br>Red, Yellow, Orange 285 145 120<br>Standard Audible 30 30 30<br>Loud Audible (Intensity 1) 30 28 25<br>Loud Audible (Intensity 2) 50 45 40<br>Loud Audible (Intensity 3) 165 90 75<br>Loud Audible (Intensity 4) 350 160 120<br>Programmable Audible 290 140 125<br>**----- End of picture text -----**<br>


## Supply Protection Circuitry 

Protected against transient voltages 

## Indicators 

1 to 6 colors depending on model (Green, Red, Yellow, Blue, White, and Orange) 

LEDs are independently selected 

Flash Rates: 1.5 Hz ±10% and 3 Hz ±10% 

## Indicator Response Time 

Off Response: 150 µs (maximum) at 12 V DC to 30 V DC On Response: 180 ms (maximum) at 12 V DC; 50 ms (maximum) at 30 V DC 

## Indicator Characteristics 

**==> picture [221 x 128] intentionally omitted <==**

**----- Start of picture text -----**<br>
Color  Lumen<br>Dominant Wavelength<br>Coordinates [(1)] Output<br>Color  (nm) or Color<br>(Typical at<br>Temperature (CCT)  x  y  25 °C)<br>Green  525 nm  –  –  92<br>Red  625 nm  –  –  40<br>Yellow  590 nm  –  –  22<br>Blue  470 nm  –  –  32<br>White  5000 K  –  –  125<br>Orange  –  0.66  0.33  33<br>**----- End of picture text -----**<br>


## Connections 

Integral 5-pin M12 male quick-disconnect connector, 8-pin M12 male quick-disconnect connector, 150 mm (5.9 in) PVC cable with an M12 male quick-disconnect connector, terminal block, or 2 m (6.5 ft) unterminated cable, depending on model 

## Terminal Block Models 

## 14 to 28 AWG wire 

## Operating Conditions 

–40 °C to +50 °C (–40 °F to +122 °F) 

95% at +50 °C maximum relative humidity (non-condensing) Environmental Rating 

IP65 

## Audible Alarm 

Standard Audible: 2.6 kHz ± 250 Hz oscillation frequency; maximum intensity (typical) 98 dB at 1 m (3.3 ft) 

Loud Audible: 2.6 kHz ± 250 Hz oscillation frequency; maximum intensity (typical) at 1 m (3.3 ft) (see table) 

**==> picture [222 x 92] intentionally omitted <==**

**----- Start of picture text -----**<br>
DIP Switches<br>Maximum Intensity (typical) at 1 meter dB<br>9  10<br>ON  ON  Intensity 4: 109 dB<br>OFF  ON  Intensity 3: 106 dB<br>ON  OFF  Intensity 2: 101 dB<br>OFF  OFF  Intensity 1: 94 dB<br>**----- End of picture text -----**<br>


## Audible Adjustment 

Standard Audible: Rotate the cover until the desired volume is reached 

Loud Audible Alarm: Select the desired volume using DIP switches 9 and 10 

Typical Reduction in Sound Intensity with Audible Adjustment (maximum to minimum): 

- Standard Audible: 8 dB 

- • Loud Audible: 15 dB 

## Construction 

Bases, Segments, Covers: polycarbonate 

## Vibration and Mechanical Shock 

Vibration: 10 Hz to 55 Hz, 0.5 mm peak-to-peak amplitude per IEC 60068-2-6 

Shock: 15G 11 ms duration, half sine wave per IEC 60068-2-27 

(1) Refer to CIE 1931 chromaticity diagram or color chart, to show equivalent color with indicated color coordinates. 

© Banner Engineering Corp. All rights reserved. www.bannerengineering.com 

page 3 of 4 

19-Aug-25 

TL70 Modular Tower Light Quick Start Guide 

## Certifications 

Banner Engineering BV Park Lane, Culliganlaan 2F bus 3 1831 Diegem, BELGIUM 

Turck Banner LTD Blenheim House Blenheim Court Wickford, Essex SS11 8YT GREAT BRITAIN 

## Required Overcurrent Protection 

WARNING: Electrical connections must be made by qualified personnel in accordance with local and national electrical codes and regulations. 

Overcurrent protection is required to be provided by end product application per the supplied table. 

Overcurrent protection may be provided with external fusing or via Current Limiting, Class 2 Power Supply. Supply wiring leads < 24 AWG shall not be spliced. For additional product support, go to www.bannerengineering.com. 

|Supply<br>Wiring<br>(AWG)<br>20|Required Overcurrent<br>Protection (A)<br>5.0|Supply<br>Wiring<br>(AWG)<br>26|Required Overcurrent<br>Protection (A)<br>1.0|
|---|---|---|---|
|22|3.0|28|0.8|
|24|2.0|30|0.5|



## Banner Engineering Corp Limited Warranty 

Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product. 

THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE. 

This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE. 

Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any time. Specifications and product information in English supersede that which is provided in any other language. For the most recent version of any documentation, refer to: www.bannerengineering.com. 

For patent information, see www.bannerengineering.com/patents. 

page 4 of 4 

© Banner Engineering Corp. All rights reserved. www.bannerengineering.com 

19-Aug-25